Inspection and Verification
Inspection and VerificationWARNING: Do not use any fluid other than clean brake fluid meeting manufacturer's specification. Additionally, do not use brake fluid that has been previously drained. Following these instructions will help prevent system contamination, brake component damage and the risk of serious personal injury.
WARNING: Carefully read cautionary information on product label. For EMERGENCY MEDICAL INFORMATION seek medical advice. In the USA or Canada on Ford/Motorcraft products call: 1-800-959-3673. For additional information, consult the product Material Safety Data Sheet (MSDS) if available. Failure to follow these instructions may result in serious personal injury.
CAUTION: Blistering or swelling of rubber brake components can indicate contamination of the brake fluid by a petroleum-based substance. Contaminated rubber components in the hydraulic brake system must be replaced and the entire hydraulic brake system must be flushed with clean, specified brake fluid to prevent recontamination.
CAUTION: Brake fluid is harmful to painted or plastic surfaces. If brake fluid is spilled on a painted or plastic surface, immediately wash it with water.
NOTE: Always check the fluid level in the brake master cylinder reservoir before carrying out any test procedures. If the fluid level is not at the correct level, clean the reservoir cap before removing, then add clean, specified brake fluid.
NOTE: Prior to carrying out any diagnosis, make sure the red brake warning indicator is functional. Refer to Instrument Panel, Gauges and Warning Indicators.
The first indication that something may be wrong in the brake system is a change in the feeling through the brake pedal. The brake warning indicator in the instrument cluster and the brake fluid level in the brake master cylinder reservoir are also indicators of system concerns.
If a wheel is locked and the vehicle must be moved, open a bleeder screw at the locked wheel to let out enough fluid to relieve the pressure. Close the bleeder screw. This bleeding operation may release the brakes but will not correct the concern. If this does not relieve the locked wheel condition, repair the locked components before proceeding.
Inspect all hoses and connections. All unused vacuum connectors should be capped. Make sure hoses and their connections are correctly secured and in good condition with no holes, soft or collapsed areas.
1. Verify the customer concern.
2. Visually inspect for obvious signs of mechanical or electrical damage.
Visual Inspection Chart
Visual Inspection Chart:
3. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
4. If the cause is not visually evident, GO to Symptom Chart - Brake System or GO to Symptom Chart - Noise, Vibration and Harshness (NVH). Symptom Chart - Brake System Symptom Chart - Noise, Vibration and Harshness (NVH)
For low or spongy brake pedal concerns:
^ check for fluid leaks. Repair as necessary.
^ check and, if necessary, refill the brake master cylinder reservoir with clean, specified brake fluid.
^ bleed the brake system and retest the brake pedal feel.
^ if the brake pedal is still low or feels spongy, check the brake pedal mounting for looseness and correct installation. Check the power brake booster and the master cylinder for loose mounting. Correct as necessary and retest the system for normal operation.
For a slow or incomplete brake pedal return concern:
^ inspect for binding, damage, correct installation or interference at the brake pedal.
^ check the power brake booster for binding, damage and correct installation.
Road Test
The technician should have a thorough knowledge of the brake system operation and accepted general braking guidelines in order to detect any problems.
Select a road that is reasonably smooth and level. Gravel or bumpy roads are not suitable because the surface does not allow the tires to grip the road equally. Avoid crowned roads.
A key factor in evaluating brake concerns is the deceleration rate. This varies from vehicle to vehicle and with changes in operating conditions. It is evident how well the brakes are working after just a few applications.
Brake Pads
NOTE: It is not required to install new brake pads if the friction material thickness is within specifications. It is also not required to install new brake pads when the brake discs are machined.
^ Remove the brake pads.
^ Inspect and measure the thickness of the brake pad friction material.
- If there are missing chunks or cracks in the lining through to the backing plate, install new brake pads.
- If the thickness of the friction material is less than the specified thickness, install new brake pads.
- If the friction material shows taper wear that is not within specifications, verify the caliper guide pins are functioning correctly.
Brake Discs
CAUTION: Using an impact tool without a torque socket will lead to unevenly tightened wheel nuts. This causes brake disc on-vehicle lateral runout and brake roughness.
NOTE: It is generally not required to install new brake discs to address noise issues.
^ Remove the brake disc.
^ Inspect the brake discs and measure the brake disc thickness in a minimum of 4 places around the circumference of the brake disc. Record the measurements.
- If the brake disc is cracked or otherwise damaged, install a new brake disc.
- If any thickness measurement is less than the minimum specification, install a new brake disc.
- If the diagnosis has revealed vibration in the steering wheel, seat or pedal while braking that varies with vehicle speed, machine the brake disc. Heavily scored brake discs, similar to that caused by pads worn down to the backing plate, should also be machined. In order to machine, discs must be above the minimum thickness to machine specification.
Brake Caliper
Inspect the brake calipers for the following:
^ Brake fluid leaks
^ Boots and seals for tears or cracks
^ Caliper piston for binding and corrosion
^ Guide pins for correct operation
Brake Caliper Guide Pins
CAUTION: Do not use power tools for caliper guide pin bore cleaning. Damage to the bore may result.
NOTE: If a guide pin kit is not available, install a new caliper assembly.
The guide pins should slide with a reasonable amount of hand force. If the brake pads show taper wear or the guide pins are difficult to move, then carry out the following steps:
1. Disassemble the guide pins.
2. Use a wire brush, rolled-up sandpaper or emery cloth to remove all corrosion and foreign material from the caliper guide pin bores. Clean remaining foreign material from the bores with brake parts cleaner and compressed air.
3. Assemble the caliper guide pins using new caliper seals, boots and guide pins. Use an ample amount of grease to lubricate the bores and guide pins.
Brake Hoses and Tubes
CAUTION: Never use copper tubing. It is subject to fatigue, cracking and corrosion, which may result in brake tube failure.
^ Double-wall steel tubing is used throughout the brake hydraulic system. All brake tube fittings must be correctly double flared to provide strong, leakproof connections. When bending tubing to fit the underbody or rear axle contours, be careful not to kink or crack the tube.
^ If a section of the brake tube is damaged, the entire section must be installed with a new tube of the same type, size, shape and length.
^ When installing the hydraulic brake tubing, hoses or connectors, tighten all connections to specifications. After installation, bleed the brake system. Refer to Brake System Bleeding.
Install a new brake flexible hose if the hose shows signs of softening, cracking or other damage.
When installing a new brake hose, position the hose to avoid contact with other vehicle components.
Non-Pressure Leaks
Two parts of the brake system that may have a brake fluid loss that does not appear when the system is under pressure are the brake master cylinder reservoir and the brake caliper under the following conditions:
Reservoir
^ Missing or poorly-fitted brake master cylinder filler cap
^ Missing or damaged brake master cylinder filler cap gasket
^ Punctured or otherwise damaged brake master cylinder reservoir
Missing, damaged or poorly-fitted sealing grommets between the brake master cylinder and the brake master cylinder reservoir
The brake master cylinder reservoir grommets are not serviceable and must be installed new as part of a new brake master cylinder and reservoir assembly.
Caliper
^ Foreign material in the caliper piston seal groove
^ Punctured or otherwise damaged caliper piston seal
The brake caliper piston seals are not serviceable and must be installed new as part of a new brake caliper.
Brake Master Cylinder - Normal Conditions
The following conditions are considered normal and are not indications that the brake master cylinder is in need of service.
Condition 1: During normal operation of the brake master cylinder, the fluid level in the brake master cylinder reservoir will fall during brake application and rise during release. The net fluid level (such as after brake application and release) will remain unchanged.
Condition 2: A trace of brake fluid will exist on the booster shell below the master cylinder mounting flange. This results from the normal lubricating action of the master cylinder bore and seal.
Condition 3: Fluid level will decrease with pad wear.
Brake Master Cylinder - Abnormal Conditions
Changes in brake pedal feel or travel are indicators that something could be wrong in the brake system. GO to Symptom Chart for abnormal condition diagnosis. Symptom Related Diagnostic Procedures
Brake Booster
Inspect the vacuum brake booster for the following:
^ Excessive corrosion or damage
^ Leaks at vacuum connections
^ Leaks or kinks in vacuum hoses
^ Correct operation of the check valve
Inspect the Hydro-Boost(R) brake booster for the following:
^ Excessive corrosion or damage
^ Fluid connections for leakage
^ Fluid hoses for kinks or leakage
Parking Brake
Check the operation of the parking brake system with the vehicle on a hoist and the parking brake control fully released. Check for any damaged cables and install new components as necessary. Check the rear brake adjustment or carry out the brake system diagnosis.