Inspection and Verification
Manual Transaxle and Clutch
Inspection and Verification
NOTICE: If transaxle noise is reported, first check the manual transmission fluid level. The vehicle should not be driven if the manual transmission fluid level is low or damage can occur.
NOTE: Before attempting to rectify any concerns, road test the vehicle to ascertain in which system the concern falls.
NOTE: If any evaluation or inspection reveals an obvious concern, repair the vehicle.
The technician should have a thorough knowledge of transaxle/clutch operation and accepted general transaxle/clutch guidelines to detect any problems.
A gear-driven unit will produce a certain amount of noise. Some noise is acceptable and audible at certain speeds or under various driving conditions. Certain conditions, such as road and weather, will amplify normal vehicle noise.
The following overview is a guide to diagnose a transaxle/clutch concern:
- Verify and document the customer concern.
- During the customer interview, if a leak was noticed or if a leak is the concern, check the manual transmission fluid. The vehicle should not be driven if the manual transmission fluid level is low.
- Check the manual transmission fluid level and condition.
- Evaluation of the clutch hydraulic system.
- Evaluation of the clutch.
- Inspect gearshift mechanism.
- Road test.
- Find the cause of the problem and correct it.
Verify Customer Concern
1. Verify and document the customer concern.
1. When was it first noticed?
2. Did it appear suddenly or gradually?
3. Did anything unusual occur that would coincide with it or precede it?
4. Identify when the condition occurs:
- Hot or cold vehicle operating conditions
- Type of terrain
- City/highway driving
- Driving at a particular speed
- coasting
- hard acceleration
- Shifting
- upshifts
- downshifts
- in a particular gear
- in all gears
- Hot or cold ambient temperatures
5. Has the transaxle/clutch been repaired before or components installed?
- Check the vehicle service record. Note any repairs.
Check Manual Transmission Fluid Level and Condition
NOTE: The vehicle should not be driven if the manual transmission fluid level is low.
An incorrect manual transmission fluid level may affect the transaxle operation and can result in transaxle damage. To correctly check and add manual transmission fluid to the transaxle, refer to transaxle draining and filling in Manual Transmission/Transaxle.
A low manual transmission fluid level can result in poor transaxle shifting, engagement or damage. It can also indicate a leak in one of the transaxle seals or gaskets.
1. Check the manual transmission fluid condition.
- Observe the color and the odor of the manual transmission fluid. Allow the manual transmission fluid to drip onto a white cloth and examine the stain. Check the manual transmission fluid for contamination or metal particles.
- Manual transmission fluid should appear nearly clear, similar to clean engine oil.
Evaluation of Clutch Hydraulic System
1. Verify that the brake/clutch hydraulic fluid reservoir is filled to the correct level.
- If the clutch hydraulic fluid level is correct, proceed to clutch check.
- If the rear chamber hydraulic fluid level is low, add fluid as necessary. Check the clutch hydraulic system for leaks and repair as necessary.
Evaluation of the Clutch
1. Depress and release the clutch pedal slowly to check if the pedal is binding. Make sure the clutch pedal can be fully depressed and is not restricted by the floor mat. Verify that the pedal return spring is present and functions correctly.
2. Measure the clutch reserve. With the engine idling, the parking brake on and the clutch pedal up, gently move the gearshift lever toward reverse gear until gear clash can be heard. Depress the clutch pedal slowly.
- If the gears cease to clash (full disengage at 1 to 38.1 mm [1.5 in] from the floor), then hold the pedal at the point of disengagement and increase engine to 4,000 rpm. The clutch should remain disengaged. If the clutch remains disengaged, the clutch is OK.
- Any concerns indicate a worn or damaged clutch. Repair as necessary.
3. With the engine idling, move the gearshift lever into 4th gear. Increase the rpm to 2,000 and slowly release the clutch pedal.
- If the engine stalls, the clutch is OK.
- If the engine does not stall, the clutch is slipping. Repair as necessary.
4. Compare the clutch evaluation results with the following table. The following list of conditions are typical faults into which clutch concerns will fall.
Inspect the Gearshift Mechanism
1. Inspect the cables for:
- signs of damage.
- broken locks.
- binding.
- cables not fully seated or in hold-down brackets.
- hold-down bracket nuts are loose.
- correct routing.
- correct adjustment.
- If the concern is a gear(s) cannot be selected, adjust the cables. Refer to Gearshift Cable Adjustment Adjustments.
2. Inspect the gearshift for:
- free play in the gearshift lever (must be no more than 5 mm [0.196 in] ). This specification is for an absolute or "no load" free play.
- If the gearshift lever free play is too great, check the gearshift cables and repair as necessary.
- If the gearshift lever free play is OK, adjust the gearshift linkage.
Evaluation of the Transmission
1. During the road test, use the following driving methods to diagnose the problem.
- Start the engine.
- Evaluate the noise in NEUTRAL while the vehicle is parked.
- Check whether the noise is present with the clutch fully disengaged (pedal fully depressed). Check to see if the pedal pulsates abnormally (for clutch diaphragm finger run out).
- Check whether the noise is present with the gearshift in the NEUTRAL position and the clutch fully engaged (foot off pedal). With the parking brake engaged, move the gearshift towards the 1st gear position. Apply very slight pressure and note if the gear noise level is reduced. (for gear rollover noise).
- With the clutch fully engaged (foot off pedal), check whether the noise is present as the engine speed is raised. If the noise reduces, note the engine speed at which this occurs.
- Listen for any change in noise while depressing and releasing the clutch pedal.
- Listen for any change in noise while changing the engine rpm.
- Drive the vehicle and shift through all of the gear ranges, including reverse. Listen for any change in noise in a particular gear.
- Drive the vehicle in the gear in which the noise is most noticeable. Depress the clutch pedal and leave the gear engaged. Listen for any change in noise.
- Drive the vehicle in the gear in which the noise is most noticeable. Depress the clutch pedal and shift the transmission into NEUTRAL. Release the clutch pedal and allow the vehicle to coast.
2. Compare the road test results with the following symptom charts. It is a list of conditions that are typical faults into which the transaxle will fall:
GO to Symptom Chart - Clutch Operation, GO to Symptom Chart - Transaxle or GO to Symptom Chart - NVH. Symptom Chart - Clutch Operation Symptom Chart - Transaxle Operation Symptom Chart - NVH