Removal
Transmission - Rear Wheel Drive (RWD)
Removal
1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Vehicle Jacking and Lifting.
2. Disconnect the battery ground cable. For additional information, refer to Battery.
3. Remove the driveshaft. For additional information, refer to Drive/Propeller Shafts, Bearings and Joints.
4. Remove the transmission fluid fill plug transmission fluid level indicator assembly located on the passenger side front portion of the transmission case. Removal of the transmission fluid fill plug will relieve any vacuum that might have built up in the transmission. This will allow the transmission fluid pan to be easily removed when the bolts are removed.
5. NOTE: If transmission disassembly or installation of a new transmission is necessary, the transmission fluid will need to be drained.
Remove the transmission fluid pan and allow the fluid to drain.
6. Install the transmission fluid pan and tighten the bolts in a crisscross pattern.
- Tighten to 12 Nm (106 lb-in).
7. Remove the selector lever cable heat shield.
8. NOTICE: To prevent selector lever cable damage, do not apply force to the selector lever cable between the manual control lever and the selector lever cable bracket.
Move the locking tab up and disconnect the selector lever cable end from the manual control lever.
1. Locking tab
2. Selector lever cable end
9. Remove the flexplate inspection cover bolts and the inspection cover.
10. Remove the rubber torque converter nut access plug.
11. Remove and discard the 4 flexplate-to-torque converter nuts.
12. Remove the transmission fluid cooler tube bracket bolt.
13. Remove the transmission-to-engine bolt.
14. Remove the transmission fluid cooler tube bracket nut and position the transmission fluid cooler tube bracket and tubes aside.
15. Remove the plastic starter motor electrical connector cap.
16. Remove the starter motor electrical connectors.
17. Remove the ground wire from the stud.
18. Remove the starter motor bolts and the starter motor.
19. Remove the LH exhaust heat shield bolt.
20. Remove the RH exhaust heat shield bolts and heat shield.
21. NOTE: LH shown, RH similar.
Disconnect the RH and LH Heated Oxygen Sensor (HO2S) and the Catalyst Monitor Sensor (CMS) connectors.
22. Remove the fuel line bracket bolt and position the fuel line bracket and fuel lines aside.
23. NOTE: Make sure that the transmission jack makes contact on the outer ribs of the fluid pan.
NOTE: Make sure that the transmission is securely fastened to the transmission jack.
Position a suitable high-lift transmission jack under the transmission.
24. Remove the 2 transmission insulator and retainer nuts.
25. Remove the 8 transmission crossmember bolts.
26. Remove the 3 transmission insulator and retainer bolts and remove the transmission insulator and retainer.
27. NOTE: LH shown, RH similar.
Remove and discard the RH and LH exhaust flange nuts.
28. Remove the 2 dual catalytic converter Y-pipe bolts, discard the nuts and remove the dual catalytic converter Y-pipe.
29. Disconnect the wire harness from the top of the transmission.
30. NOTICE: Do not pull on the transmission vehicle harness to disconnect the connector or damage to the connector will occur.
Disconnect the transmission vehicle harness connector by twisting the outer shell and pulling back on the connector.
31. NOTE: The top 2 transmission-to-engine bolts need to be removed prior to removing the remaining bolts.
NOTE: The top left bolt secures the fuel line bracket to the transmission case.
Remove the 6 remaining transmission-to-engine bolts.
32. Slide the transmission back far enough to install the Torque Converter Retainer.
33. Remove the transmission from the vehicle.
34. If the transmission is being disassembled to install new parts, or if a new or remanufactured transmission is being installed, the transmission fluid cooler, the auxiliary transmission fluid cooler (if equipped) and the transmission fluid cooler tubes must be cleaned and backflushed to keep contaminants from entering the transmission. For additional information, refer to Transmission Fluid Cooler Backflushing and Cleaning 6R80.