Pinpoint Test Y: DTC B103C
Seats
Pinpoint Tests
Pinpoint Test Y: DTC B103C
Refer to Wiring Diagram Set 119, Climate Controlled Seats for schematic and connector information. Diagrams By Number
Normal Operation
The seat cushion and backrest are equipped with a Thermo-Electric Device (TED) assembly that includes a seat blower (fan motor, serviced as an assembly with the TED). If the Dual Climate Controlled Seat Module (DCSM) detects an open circuit or high TED resistance, the following DTC will be set:
- DTC B103C (Thermo-Electric Driver Open Load) - If DCSM outputs to the driver seat backrest or cushion TED (circuit pin G, H, J or K at the DCSM connector) or any components within these circuit loops are open, disconnected or a TED resistance greater than 90,000 ohms is sensed, the DCSM continues normal operation and sets this DTC.
This pinpoint test is intended to diagnose the following:
- Wiring, terminals or connectors
- TED assembly
- DCSM
PINPOINT TEST Y: DTC B103C
NOTE: The air bag warning indicator illuminates when the correct Restraints Control Module (RCM) fuse is removed and the ignition is ON.
NOTE: The Supplemental Restraint System (SRS) must be fully operational and free of faults before releasing the vehicle to the customer.
-------------------------------------------------
Y1 CHECK THE TED CIRCUITS FOR AN OPEN
- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering in the General Procedures portion of Restraint Systems.
- Disconnect: Driver Seat Side Air Bag Module C3051.
- Disconnect: Passenger Seat Side Air Bag Module C339.
- Disconnect: DCSM C3265A.
- Disconnect: Cushion TED C3035.
- Disconnect: Backrest TED C3034.
- Measure the resistance between DCSM C3265A, harness side and cushion TED C3035, harness side; and between DCSM C3265A, harness side and backrest TED C3034, harness side using the following chart:
- Are the resistances less than 5 ohms?
Yes
GO to Y2.
No
REPAIR the circuit(s). CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable. CONNECT driver seat side air bag module C3051 and passenger seat side air bag module C339. REPOWER the SRS. REFER to Restraint Systems.
-------------------------------------------------
Y2 CHECK THE TED CIRCUITS FOR A SHORT TO VOLTAGE
- WARNING: Make sure no one is in the vehicle and there is nothing blocking or placed in front of any air bag module when the battery is connected. Failure to follow these instructions may result in serious personal injury in the event of an accidental deployment.
- Connect the battery ground cable. Refer to Battery.
- Ignition ON.
- Measure the voltage between DCSM C3265A, harness side and ground using the following chart:
- Is voltage present on either circuit?
Yes
REPAIR the circuit(s). CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable. CONNECT driver seat side air bag module C3051 and passenger seat side air bag module C339. REPOWER the SRS. REFER to Restraint Systems.
No
GO to Y3.
-------------------------------------------------
Y3 CHECK THE BACKREST TED AND CUSHION TED RESISTANCES
- Ignition OFF.
- Measure the resistance between:
- backrest TED C3034 pins 1 and 3, component side.
- cushion TED C3035 pins 1 and 3, component side.
- Are the resistances between 0.9 and 10 ohms?
Yes
INSTALL a new DCSM. REFER to Dual Climate Controlled Seat Module (DCSM) Dual Climate Controlled Seat Module (DCSM). CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable. CONNECT driver seat side air bag module C3051 and passenger seat side air bag module C339. REPOWER the SRS. REFER to Restraint Systems.
No
If the backrest TED resistance is not between 0.9 and 10 ohms, INSTALL a new backrest TED. REFER to Seat Backrest Thermo-Electric Device Seat Backrest Thermo-Electric Device. CLEAR the DTCs. REPEAT the self-test.
If the cushion TED resistance is not between 0.9 and 10 ohms, INSTALL a new cushion TED. REFER to Seat Cushion Thermo-Electric Device Seat Cushion Thermo-Electric Device. CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable. CONNECT driver seat side air bag module C3051 and passenger seat side air bag module C339. REPOWER the SRS. REFER to Restraint Systems.
-------------------------------------------------