Program a MyKey(TM)

MyKey(TM) Programming

Program a MyKey(TM)

With Three Button Message Center

NOTE: After a MyKey(TM) has been programmed, the remaining standard key(s) (the key[s] that is not programmed with the MyKey(TM) feature) is referred to as an "administrator key(s)" or "admin" key(s). There must always be at least one admin key. The Instrument Cluster (IC) does not allow the last admin key to be programmed into a MyKey(TM) restricted key. Both the admin key and the MyKey(TM) restricted key can be used to see how many MyKey(TM) and admin keys are programmed to the vehicle, and how many total miles have been driven with the MyKey(TM) feature active (using the message center). The MyKey(TM) is the one with the restricted status. The admin key does not have any restrictions.

NOTE: The MyKey(TM) feature can be cleared within the same key cycle that it was programmed. Follow the Disable MyKey(TM) procedure to clear the key of any restricted MyKey(TM) status. If the key has been cycled, an admin key is required to disable the MyKey(TM) programming.

NOTE: The MyKey(TM) feature can only be configured or disabled with an admin key.

1. Insert a programmed PATS ignition key into the ignition lock cylinder and turn the key from the OFF to the ON position. This key must be the one that is being programmed to the MyKey(TM) restricted status.

2. Press the SETUP button until PRESS RESET TO CREATE MYKEY appears in the message center display.

3. Press and release the RESET button. HOLD RESET TO CONFIRM MYKEY is displayed.

4. Press and hold the RESET button (for approximately 2 seconds) until MARK THIS KEY AS RESTRICTED is displayed.

5. Wait until KEY RESTRICTED AT NEXT START is displayed, then release the RESET button.

6. The MyKey(TM) feature (standard restricted features) is successfully programmed into this particular key. Make sure it is labeled for easy identification. If you would like to customize the MyKey(TM) with the audio volume limited, maximum speed limit, speed alert chimes, and AdvanceTrac(R) on/off restrictions, refer to Configuring MyKey(TM) Optional Restricted Features. Configuring MyKey(TM) Optional Restricted Features
- If the vehicle is equipped with remote start, also refer to Using MyKey(TM) with Remote Start Systems. Using MyKey(TM) with Aftermarket Remote Start System

With Single Stem Message Center

NOTE: After a MyKey(TM) has been programmed, the remaining standard key(s) (the key[s] that is not programmed with the MyKey(TM) feature) is referred to as an "administrator key(s)" or "admin" key(s). There must always be at least one admin key. The IC does not allow the last admin key to be programmed into a MyKey(TM) restricted key. The MyKey(TM) is the one with the restricted status. The admin key does not have any restrictions.

NOTE: The MyKey(TM) feature can be cleared within the same key cycle that it was programmed. Follow the Disable MyKey(TM) Restricted Features procedure to clear the key of any restricted MyKey(TM) status. If the key has been cycled, an admin key is required to disable the MyKey(TM) programming.

NOTE: The MyKey(TM) feature can only be configured or disabled with an admin key.

1. Insert a programmed PATS ignition key into the ignition lock cylinder and turn the key from the OFF to the ON position. This key must be the one that is being programmed to the MyKey(TM) restricted status.

2. Press the SELECT/RESET button until PRESS RESET TO CREATE MYKEY appears in the message center display.

3. Press and hold the SELECT/RESET button. HOLD RESET TO CONFIRM MYKEY is displayed.

4. Press and hold the SELECT/RESET button until MARK THIS KEY AS RESTRICTED is displayed.

5. Wait until KEY RESTRICTED AT NEXT START is displayed, then release the SELECT/RESET button.

6. The MyKey(TM) feature (standard restricted features) is successfully programmed into this particular key. Make sure it is labeled for easy identification. If you would like to customize the MyKey(TM) with the audio volume limited, maximum speed limit, speed alert chimes, and AdvanceTrac(R) on/off restrictions, refer to Configuring MyKey(TM) Optional Restricted Features. Configuring MyKey(TM) Optional Restricted Features
- If the vehicle is equipped with remote start, also refer to Using MyKey(TM) with Remote Start Systems. Using MyKey(TM) with Aftermarket Remote Start System