Pinpoint Test AB: DTC B111C
Seats
Pinpoint Tests
Pinpoint Test AB: DTC B111C
Refer to Wiring Diagram Set 119, Climate Controlled Seats for schematic and connector information. Diagrams By Number
Normal Operation
Climate controlled seats are independently controlled by the Dual Climate Controlled Seat Module (DCSM) mounted to the bottom of the passenger seat cushion. The climate controlled seat system only operates with the engine running, however, if using a scan tool to command the DCSM, diagnostic testing can be carried out with the ignition ON. The system receives voltage from Battery Junction Box (BJB) fuse 69 (30A) supplying battery voltage into DCSM C3265A pins E and F. If voltage is disconnected from either pin E or F of DCSM C3265A with the voltage connection remaining on the other circuit, both seats will remain operational because the voltage supply circuits are connected internally in the DCSM. However, if a fault occurs setting a DTC specific to either climate controlled seat, only the affected seat will be disabled by the module and the other will remain operational.
The seat cushion is equipped with a Thermo-Electric Device (TED) assembly that includes a seat blower (fan motor, serviced as an assembly with the TED). Similarly, the seat backrest is also equipped with its own TED assembly with blower. Cabin air is drawn through the blower and distributed to each of the TED modules located in the seat cushion and backrest. The TEDs then heat or cool the air. The air is then directed into the foam pad and manifold where it is distributed along the surface of the cushion and backrest of the seat. Once the system is activated, the DCSM uses a set of flexible algorithms to control the heating/cooling modes and the blower speed dependant on the HVAC module seat switch settings.
- DTC B111C (Passenger Thermo-Electric Driver Open Load) - If DCSM outputs to the passenger seat backrest or cushion TED (circuit pins A, B, C or D at the DCSM connector) or any components within these circuit loops are open, disconnected or a TED resistance greater than 90,000 ohms is sensed, the DCSM continues normal operation and sets this DTC.
This pinpoint test is intended to diagnose the following:
- Wiring, terminals or connectors
- TED assembly
- DCSM
PINPOINT TEST AB: DTC B111C
NOTE: The air bag warning indicator illuminates when the correct Restraints Control Module (RCM) fuse is removed and the ignition is ON.
NOTE: The Supplemental Restraint System (SRS) must be fully operational and free of faults before releasing the vehicle to the customer.
-------------------------------------------------
AB1 CHECK THE TED CIRCUITS FOR AN OPEN
- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering in the General Procedures portion of Restraint Systems.
- Disconnect: Passenger Seat Side Air Bag Module C339.
- Disconnect: DCSM C3265A.
- Disconnect: Cushion TED C3040.
- Disconnect: Backrest TED C3039.
- Measure the resistance between DCSM C3265A, harness side and cushion TED C3040, harness side; and between DCSM C3265A, harness side and backrest TED C3039, harness side using the following chart:
- Are the resistances less than 5 ohms?
Yes
GO to AB2.
No
REPAIR the circuit(s). CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable. CONNECT passenger seat side air bag module C339. REPOWER the SRS. REFER to Restraint Systems.
-------------------------------------------------
AB2 CHECK THE TED CIRCUITS FOR A SHORT TO VOLTAGE
- WARNING: Make sure no one is in the vehicle and there is nothing blocking or placed in front of any air bag module when the battery is connected. Failure to follow these instructions may result in serious personal injury in the event of an accidental deployment.
- Connect the battery ground cable. Refer to Battery.
- Ignition ON.
- Measure the voltage between DCSM C3265A, harness side and ground using the following chart:
- Is voltage present on any circuits?
Yes
REPAIR the circuit(s). CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable. CONNECT passenger seat side air bag module C339. REPOWER the SRS. REFER to Restraint Systems.
No
GO to AB3.
-------------------------------------------------
AB3 CHECK THE BACKREST TED AND CUSHION TED RESISTANCES
- Ignition OFF.
- Measure the resistance between:
- backrest TED C3039 pins 1 and 3, component side.
- cushion TED C3040 pins 1 and 3, component side.
- Are the resistances between 0.9 and 10 ohms?
Yes
INSTALL a new DCSM. REFER to Dual Climate Controlled Seat Module (DCSM) Dual Climate Controlled Seat Module (DCSM). CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable. CONNECT passenger seat side air bag module C339. REPOWER the SRS. REFER to Restraint Systems.
No
If the backrest TED resistance is not between 0.9 and 10 ohms, INSTALL a new backrest TED. REFER to Seat Backrest Thermo-Electric Device Seat Backrest Thermo-Electric Device. CLEAR the DTCs. REPEAT the self-test.
If the cushion TED resistance is not between 0.9 and 10 ohms, INSTALL a new cushion TED. REFER to Seat Cushion Thermo-Electric Device Seat Cushion Thermo-Electric Device. CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable. CONNECT passenger seat side air bag module C339. REPOWER the SRS. REFER to Restraint Systems.
-------------------------------------------------