Seat Belt Systems: Description and Operation

Safety Belt System

WARNING: After any crash, all of the following safety belt assemblies and attaching hardware must be inspected by an authorized dealer to verify correct function:
- Retractors
- Buckles
- Belt tension sensor (BTS) (if equipped)
- Front safety belt buckle support assemblies (slide bar) (if equipped)
- Safety belt shoulder belt height adjusters (if equipped)
- Child safety seat tether bracket assemblies
- Automatic locking retractor (ALR) feature for child safety seats (passenger seating positions only)
If any safety belt assembly is damaged, does not operate correctly or does not pass all of the Functional Tests in the Diagnosis and Testing, a new safety belt assembly must be installed. If any safety belt assembly attaching areas are damaged or distorted, the sheet metal must be restored to its original structural integrity and new safety belt assembly and attaching hardware must be installed. Failure to install new safety belt assemblies and attaching hardware may increase the risk of serious personal injury or death in a crash.

After any crash that results in deployment of the driver and/or front outboard passenger safety belt pretensioners, new driver and/or front outboard passenger safety belt systems (including retractors, buckles and height adjusters) must be installed. Failure to install new safety belt systems increases the risk of serious personal injury or death in a crash.

When new active occupant restraint components are installed, use only replacement parts specified in the Ford Catalog Advantage(TM) or equivalent.

The active restraint system consists of the following serviceable items:

- Front safety belt buckles, attached to the inboard side of the driver and passenger seat tracks
- Front center safety belt attached to the LH side of the front center seat base frame
- Front center safety belt buckle attached to the RH side of the front center seat base frame
- Detachable safety belt anchor attached to the LH side front center seat base frame (regular cab)
- Front safety belt retractors and pretensioners, located behind the B-pillar trim panels (Crew Cab and regular cab) or in the rear door (SuperCab)
- Front center safety belt retractor, attached to the back panel of the cab (regular cab)
- Belt Tension Sensor (BTS), located at the safety belt anchor point of the front passenger outboard safety belt
- Rear outboard safety belt retractors, located behind the B-pillar trim panels (SuperCab) or C-pillar trim panels (Crew Cab)
- Rear center safety belt retractor attached to the back panel of the cab
- RH rear safety belt buckles, attached to the floor pan (SuperCab)
- RH rear safety belt buckles, seat mounted and attached to the seat risers (Crew Cab)
- LH rear safety belt buckles attached to the floor pan (SuperCab and Crew Cab)
- Rear child safety seat tether anchors, at all seating positions, attached to the back panel of the cab


Safety Belt Retractors

- Dual locking mode
- Emergency Locking Retractor (ELR)
- Automatic Locking Retractor (ALR) (all except driver seat and regular cab center seat)

- Safety belt retractors and pretensioners (front outboard only)
- BTS (front outboard passenger only)

Automatic Locking Retractor (ALR)

The ALR mode is used when locking a child seat in an outboard seating position. The ALR mode is automatically activated when the safety belt webbing is fully extracted from the retractor and then allowed to retract. As the safety belt webbing is retracted back onto the spool, an audible clicking sound is made indicating the safety belt retractor is in ALR mode and the safety belt webbing will not pull back out of the safety belt retractor. To disengage the ALR mode, allow the safety belt webbing to fully retract back onto the spool. The ALR mode is disengaged when the webbing is free to extract and retract back into the retractor. For testing, refer to the appropriate Functional Test procedure in Safety Belt System Component Tests and General Diagnostics.

Emergency Locking Retractor (ELR)

The ELR is a vehicle-sensitive feature designed to activate and lock the safety belt webbing during hard braking, hard cornering or in an impact of approximately 24 km/h (15 mph). The ELR feature helps to reduce the forward movement of the driver and passengers. For testing, refer to the appropriate Functional Test procedure in Safety Belt System Component Tests and General Diagnostics.

Safety Belt Retractors and Pretensioners

The pretensioner is a pyrotechnic device that deploys when activated by the Restraints Control Module (RCM) to remove excess safety belt webbing from the shoulder and lap safety belt in the event of an impact. If a deployment of the safety belt retractor and pretensioners occurs, a new assembly must be installed. Refer to Safety Belt Retractor and Pretensioner - Regular Cab and Crew Cab Safety Belt Retractor and Pretensioner - Regular Cab and Crew Cab or Safety Belt Retractor and Pretensioner - SuperCab Safety Belt Retractor and Pretensioner - SuperCab.

For safety belt retractor and pretensioner diagnostic and disposal information, refer to Restraint Systems.

Belt Tension Sensor (BTS)

The BTS is located at the RH front safety belt retractor and pretensioner anchor point and operates as part of the Occupant Classification Sensor (OCS) system. To diagnose the BTS, refer to Restraint Systems.


Safety Belt Buckles

Front Safety Belt Buckles

The safety belt buckles are attached to the inboard side of the driver and passenger seat tracks and if equipped, to the RH side of the center seat base frame.

After any crash, safety belt buckles must be inspected to verify correct function.

Rear Safety Belt Buckles

On the SuperCab, the RH rear safety belt buckles are attached to the floor and the LH rear safety belt buckle is part of the rear center safety belt retractor and attaches to the floor. On the Crew Cab, the RH rear safety belt buckles are attached to the seat risers and the LH rear safety belt buckle is part of the rear center safety belt retractor and attaches to the floor.

After any crash, safety belt system components (including retractors and buckles) must be inspected to verify correct function.


Child Safety Seat Restraints

The child safety seat restraints include the following items:

- Non-serviceable child safety seat tether anchors attached to the rear seat risers on the SuperCab and Crew Cab. The attachment points protrude from the bight line between the seat cushion and seat backrest.
- Serviceable rear child safety seat tether anchors, at all seating positions, attached to the back panel of the cab.

If a child safety seat was in use during a collision, inspect the child safety seat component mounting areas and repair any damage and restore the vehicle to the original production configuration.