Climate Control System

Climate Control System

Component Tests


Blower Motor Resistor











Auxiliary Blower Motor Resistor











Heater Core

1. NOTE: If a heater core leak is suspected, the heater core must be tested by following the plugged heater core component test before the heater core pressure test. Carry out a system inspection by checking the heater system thoroughly as follows:

Inspect for evidence of coolant leakage at the heater water hose to heater core attachments. A coolant leak in the heater water hose could follow the heater core tube to the heater core and appear as a leak in the heater core.

2. NOTE: Spring-type clamps are installed as original equipment. Installation and overtightening of non-specification clamps can cause leakage at the heater water hose connection and damage the heater core.

Check the integrity of the heater water hose clamps.


Heater Core - Plugged

1. Check to see that the engine coolant is at the correct level.

2. Start the engine and turn on the heater.

3. When the engine coolant reaches operating temperature, feel the heater core inlet and outlet hose to see if they are hot.
- If the inlet hose is not hot:
- the thermostat is not working correctly.

- If the outlet hose is not hot:
- the heater core may have an air pocket.

- the heater core may be restricted or plugged.


Heater Core - Pressure Test

Use the Pressure Test Kit to carry out the pressure test.

1. NOTE: Due to space limitations, a bench test may be necessary for pressure testing.

Drain the coolant from the cooling system. Refer to Engine Cooling Cooling System Draining, Filling and Bleeding.

2. Disconnect the heater hoses from the heater core. Refer to Climate Control Heater Core.

3. Install a short piece of heater hose, approximately 101 mm (4 in) long on each heater core tube.

4. Fill the heater core and heater hoses with water and install Plug BT-7422-B and adapter BT-7422-A from the Pressure Test Kit in the heater hose ends. Secure the heater hoses, plug and adapter with hose clamps.






5. Attach the pump and gauge assembly from the Radiator/Heater Core Pressure Tester to the adapter.

6. Close the bleed valve at the base of the gauge. Pump 138 kPa (20 psi) of air pressure into the heater core.

7. Observe the pressure gauge for a minimum of 3 minutes.

8. If the pressure drops, check the heater hose connections to the core tubes for leaks. If the heater hoses do not leak, remove the heater core from the vehicle and carry out the bench test.


Heater Core - Bench Test

1. Remove the heater core from the vehicle. Refer to Climate Control Heater Core.

2. Drain all of the coolant from the heater core.

3. Connect the 101 mm (4 in) test heater water hoses with plug and adapter to the core tubes. Then connect the radiator/heater core pressure tester to the adapter.

4. Apply 138 kPa (20 psi) of air pressure to the heater core. Submerge the heater core in water.

5. If a leak is observed, install a new heater core.






Evaporator/Condenser Core - On-Vehicle Leak Test

1. Discharge and recover the refrigerant. Refer to Air Conditioning (A/C) System Recovery, Evacuation and Charging Air Conditioning (A/C) System Recovery, Evacuation and Charging.

2. NOTE: DO NOT leak test an evaporator core with the suction accumulator attached to the evaporator core tubes.

Disconnect the suspect evaporator core Evaporator Core or condenser core Service and Repairfrom the A/C system.

3. Clean the spring lock couplings. Refer to Spring Lock Coupling Spring Lock Coupling.

4. Connect the appropriate test fittings from the A/C Flush and Purge Fitting Kit to the evaporator or condenser tube connections.

5. NOTE: The automatic shut-off valves on some gauge set hoses do not open when connected to the test fittings. If available, use hoses without shut-off valves. If hoses with shut-off valves are used, make sure the valve opens when attached to the test fittings or install an adapter which will activate the valve. The test is not valid if the shut-off valve does not open.

Connect the red and blue hoses from the R134-a Manifold Gauge Set to the test fittings on the evaporator core or condenser core. Connect the yellow hose to a known good vacuum pump.

6. Open both gauge set valves and start the vacuum pump. Allow the vacuum pump to operate for a minimum of 45 minutes after the gauge set low pressure gauge indicates 101 kPa (30 in-Hg). The 45 minute evacuation is necessary to remove any refrigerant from oil left in the evaporator core or condenser core. If the refrigerant is not completely removed from the oil, outgassing will degrade the vacuum and appear as a refrigerant leak.

7. If the low pressure gauge reading will not drop to 101 kPa (30 in-Hg) when the valves on the gauge and manifold set are open and the vacuum pump is operating, close the gauge set valves and observe the low pressure gauge. If the pressure rises rapidly to zero, a large leak is indicated. Recheck the test fitting connections and gauge set connections before installing a new evaporator core or condenser core.

8. After evacuating for 45 minutes, close the gauge set valves and stop the vacuum pump. Observe the low pressure gauge; it should remain at the 101 kPa (30 in-Hg) mark.
- If the low pressure gauge reading rises 34 or more kPa (10 or more in-Hg) of vacuum from the 101 kPa (30 in-Hg) position in 10 minutes, a leak is indicated.

- If a very small leak is suspected, wait 30 minutes and observe the vacuum gauge.

- If a small amount of vacuum is lost, operate the vacuum pump with gauge valves open for an additional 30 minutes to remove any remaining refrigerant from the oil in the evaporator core or condenser core. Then recheck for loss of vacuum.

- If a very small leak is suspected, allow the system to set overnight with vacuum applied and check for vacuum loss.

9. If the evaporator core or condenser core does leak, as verified by the above procedure, install a new evaporator core Evaporator Core or condenser core Service and Repair.


A/C Compressor - External Leak Test

1. Install the A/C pressure test adapter on the rear head of the A/C compressor using the existing manifold retaining bolt.

2. Connect the high and low pressure lines of a manifold gauge set or a refrigerant recovery/recycling station to the corresponding fittings on the A/C pressure test adapter.

3. Attach the center hose of the manifold gauge set to a refrigerant container standing in an upright position.

4. Open the low pressure gauge valve, the high pressure gauge valve and the valve on the refrigerant container to allow the refrigerant vapor to flow into the A/C compressor.

5. Using a refrigerant leak detector, check for leaks at the compressor shaft seal, the compressor front/rear head seal and the compressor rear head bolts.

6. If an external leak is found, install a new A/C compressor. Refer to Climate Control Service and Repair.

7. When the leak test is complete, recover the refrigerant from the compressor.