Fuel - Diagnosis for Surge Hot/Cold, Detonation, Code 32

91chevy26

GMC NUMBER: 89-6E-140

GROUP: 6E Engine Emissions

DATE: November, 1991


CORPORATE NUMBER: 136516


SUBJECT: ENGINE DRIVEABILITY - SURGE HOT/COLD, DETONATION (DIAGNOSIS, REPLACEMENT PARTS)

MODELS: 1987-89 C/K AND R/V/G/P WITH 7.4L ENGINE


THIS CANCELS AND REPLACES THE FOLLOWING GMC TRUCK BULLETINS:
88-T-141 (AUG 88), 88-T-95 (APR 88), AND 89-6E-106 (OCT 89). ALL COPIES OF THESE BULLETINS SHOULD BE DESTROYED.

Some 1987-89 C/K and R/V/G/P trucks with 7.4L engine may experience the following:

1. Surge on acceleration and/or at road load speeds

2. False Service Engine Soon Light - Code 32 (EGR)

3. Poor driveability during warm up

4. Detonation under load


SERVICE PROCEDURE:

1. On 1987-89 models, check for vacuum leaks including;

A. TBI Base gasket to adapter

B. TBI Adapter to TBI

C. Re-torque intake manifold to 30 lbs.ft.

2. On 1987-89 models, check base timing (Spec. 4 degrees BTDC).

View A:

View B:

3. On 1987-88 models only, relocate map sensor to air cleaner.

A. Check map sensor operation using procedures on pages 3-122 and 3-123 of the 1991 Light Duty Fuel and Emissions Manual; replace sensor if necessary.

B. Disconnect vacuum tube assembly and electrical connection from map sensor.

C. Remove map sensor from upper plastic bracket (see illustration, View B). CARE MUST BE TAKEN TO AVOID BREAKING BRACKET.


D. Remove sheet metal screw holding upper plastic bracket to lower metal bracket, and retain plastic bracket.

View C:

View D:

View E:

E. Add one additional 3/16" hole to plastic bracket and two 1/8" holes in air cleaner at proper location, using revised bracket as hole template (Views C and D).

F. Mount bracket so map sensor vacuum connection faces down toward engine, using two 8-3x1/2" sheet metal screws, P/N 447164.

G. Install vacuum hose harness, P/N 10129600 (see Views D and E).

Important

On trucks not equipped with an accessory vacuum fitting in the manifold, install fitting, P/N 14088336 and use caps, P/N 343350 to plug any unused port.

H. Reinstall electrical.

4. On 1987-89, Check the control idle speed.

A. On fully warm engine, Spec. is 750 RPM in Drive for automatic transmission and 800 RPM in Neutral for manual transmission.
B. IAC counts on both transmission should be between 5-30 counts.

^ If the control speed is not within the above specifications, a minimum idle speed adjustment must be made using the procedure shown on page 4-20 of the 1991 Light Duty Fuel and Emissions Manual.


5. Install latest PROM as shown in PARTS INFORMATION.

6. The Dealer should tell the customer that the Cold Start Procedure has been revised from that shown in the Owner's Manual. After initial


fire and run, the throttle should be cracked to about 1/4 to clean raw gas from the intake manifold.


PARTS INFORMATION:

TRANSMISSION AXLE NEW PROM KIT NEW BROADCAST NEW SCAN TOOL
CODE I.D.

Auto (M-40) ALL 16169157 AZFT 9171
Man (M-20) 3.73 (GT4) 16169158 AZFU 9181
3.42 (GU6) " " "
Man (M-20) 4.10 (GT5) 16169159 AZFW 9191
4.56 (HG4) " " "

Parts are currently available from GMSPO.

WARRANTY INFORMATION:
LABOR
OPERATION LABOR TIME
NUMBER:
Relocating Map
Sensor T7500 0.3 Hours

Replace PROM T0500 0.6 Hours C/K,
R/V
0.7 Hours G/P