Sliding Door - Binding on Opening
91chevy12
GMC NUMBER: 91-10-80
GROUP: 10-A1 Doors
DATE: March, 1991
CORPORATE
NUMBER: 061013R
SUBJECT: SLIDING DOOR OPENING AND CLOSING EFFORT
MODELS: 1989-91 M/L VANS - STANDARD LENGTH
Some of the above subject vehicles may experience a binding condition during sliding door opening. This condition can be caused by a broken or worn center track roller bearing. If the center track roller bearing breaks or has excessive wear, the sliding door operating effort increases and may deform the center track. This condition may occur when opening or shutting the door. To correct, it is necessary to replace the center track roller bracket, center track assembly and install a new lower track striker/bumper assembly. A new lower track striker/bumper assembly is necessary to prevent door components from being damaged when the door is forcefully opened. The only difference between the new lower track striker/bumper assembly and original assembly is bolt hole locations. The hole locations have been moved rearward approximately 15 mm.
VEHICLES INVOLVED Use the new Striker/bumper assembly on vehicles built prior to the following VINs:
GMC 1GTDM15B5BM503571
CHEVROLET 1GCDM15B5BM112077
Figure 1 - Center Track Roller Bracket:
Figure 3 - Center Roller Track:
Figure 2 - Track Cover:
Figure 4 - Lower Striker/Bumper Assembly:
SERVICE PROCEDURE: (Refer to Figures 1-4).
1. Remove jack cover.
2. Remove interior quarter panel trim, if equipped.
3. Remove taillight assembly.
4. Remove track cover retainer bolts and remove the cover. Visually inspect the cover, if damaged replace.
5. Remove interior quarter trim molding, if equipped.
6. Remove center roller track.
7. Remove three screws from sliding door latch assembly and lay aside.
8. Support door weight at rear edge of door using a padded floor jack.
9. Remove pin from center track roller bracket door hinge.
10. Remove and discard roller bracket assembly from center track.
11. Remove center track nuts and bolts. Inspect track, if damaged replace.
12. Remove two torx head screws on the lower track rear side door catch striker/bumper assembly, remove and discard the assembly.
13. Using existing screws and existing body assembly holes, install a new lower track rear side door catch striker/bumper assembly (P/N 15683553). Torque screws to 20-30 N-m (15-22 lbs.ft.).
14. Reinstall the center roller bracket track using the existing nuts and bolt. Torque the nuts to 6-9 N-m (4-7 lbs.ft.). Torque the bolt to 10-14 N-m (8-10 lbs.ft.).
15. Install new rear side door center roller bracket assembly (P/N 15642131) to center roller track.
16. Reinstall existing pin through center track roller bracket door hinge and roller bracket assembly.
17. Remove padded floor jack from rear edge of door.
18. Reinstall sliding door latch assembly using three existing screws. Torque screws to 6.4-10.0 N-m (5-8 lbs.ft.).
19. Reinstall the track cover (or if damaged, replace) using the existing retainer bolts. Torque the bolts to 1.2-1.6 N-m (11-14 lbs.in.). If the track cover requires replacement, paint to match.
20. Reinstall the taillight assembly.
21. Reinstall the interior quarter trim panel, if equipped.
22. Reinstall interior quarter trim molding, if equipped.
23. Reinstall the jack cover.
24. Check door operation.
SERVICE PARTS INFORMATION:
Part Description Quantity
Number Required
15683553 Striker Asm.-Rear Side Door 1
15642131 Bracket Asm.-Rear Side Door 1
Center Roller
15563740 Center Track Asm.-Side Door 1
155713231 Center Track Cover Asm. 1
Parts are currently available from GMSPO.
WARRANTY INFORMATION For vehicles repaired under warranty use:
Labor Operation: T7171 (Replaces center roller
bracket, center track assembly,
center track cover and lower
striker/bumper bracket modifi-
cation.)
Labor Time: 0.9 hr.
NOTE: Labor Operation is coded to base vehicle coverage in the warranty system.