Ignition Lock Cylinder & Upper Column Components - Column Shift

INCLUDES:
STEERING SHAFT LOCK
TURN SIGNAL CANCELLING CAM ASM
UPPER BEARING SPRING
THRUST WASHER
TURN SIGNAL SWITCH ASSEMBLY
BUZZER SWITCH ASSEMBLY
STRG COLUMN LOCK CYLINDER SET

TOOLS REQUIRED:
^ J 23653-C Lock Plate Compressor

IMPORTANT
^ Before doing any service procedures in this section, removal of Steering Wheel is needed.

Fig. 13 Exploded View Of Standard Steering Column W/ Column Shift:

Standard Steering Column - Legend:

REMOVE OR DISCONNECT
1. Negative (-) battery cable.
2. Shaft lock cover (2).
3. Shaft lock retaining ring (3) using J 23653-C to push down steering shaft lock (4). Dispose of ring (3).

Removing Shaft Lock Retaining Ring:

4. Shaft lock (4) from steering shaft assembly (40).
5. Turn signal cancelling cam assembly (5).
6. Upper bearing spring (6).
7. Thrust washer (12).
8. Turn signal to "RIGHT TURN" position (up).
9. Multi-function lever and hazard knob assembly.
10. Washer head screw (8) and switch actuator arm (9).
11. Three cross recess screws (7).

Turn Signal Switch Removal Preparation:

Removing Turn Signal Switch:

12. Turn signal switch assembly (10).
^ Let switch hang freely.
^ To remove switch (10):
A. Hex head bolts (53).
B. Steering column support bracket assembly (52).
C. Turn signal switch connector from vehicle wire harness.
D. Wiring protectors (33) and (34).
E. Gently pull wire harness through column.
13. Key from steering column lock cylinder set (17).
14. Buzzer switch assembly (13).
15. Insert key in lock cylinder (17).
^ Key in "lock" position.
16. Lock retaining screw (14).

Removing Components From Upper Shaft:

17. Steering column lock cylinder set (17).

INSTALL OR CONNECT

NOTICE: Ensure all fasteners are securely seated before applying needed torque. Failure to do may result in component damage or malfunctioning of steering column.

1. Steering column lock cylinder set (17).
2. Lock retaining screw (14).

TIGHTEN
^ Tighten screw (14) to 4.5 Nm (40 lb.in.).

3. Key from lock cylinder set (17).
4. Buzzer switch assembly (13).
5. Reinsert key in lock cylinder set (17).
^ Key in "lock" position.
6. Turn signal switch assembly (10) wire harness through steering column.
A. Let switch hang freely.
B. Switch connector to vehicle wire harness.
C. Wiring protectors (33) and (34).
D. Support bracket (52).
E. Hex head bolts (53).

TIGHTEN
^ Tighten bolts (53) to 30.0 Nm (22 lb.ft.).

7. Turn signal switch (10) and three screws (7).

TIGHTEN
^ Tighten screws (7) to 3.4 Nm (30 lb.in.).

8. Switch actuator arm (9) and screw (8).

TIGHTEN
^ Tighten screw (8) to 2.3 Nm (20 lb.in.).

9. Hazard knob assembly and multi-function lever.
10. Thrust washer (12).
11. Upper bearing spring (6).
12. Turn signal cancelling cam assembly (5). Lubricate with grease, synthetic (service kit).
13. Shaft lock (4).
14. New shaft lock retaining ring (3) using J 23653-C to push down shaft lock (4).
^ Ring (3) must be firmly seated in groove on shaft.
15. Shaft lock cover (2).

NOTICE: Gently pull lower turn signal wires to remove any wire kinks that may be inside steering column assembly. Failure to do so may cause damage to wire harness.

16. Refer to "Steering Column Components Replacement" to complete remaining steering column assembly.
17. Negative (-) battery cable.