Ignition Lock Cylinder, Shrouds

^ Tools Required:
- J 41352 Modular Column Holding Fixture
- Or Equivalent

REMOVE OR DISCONNECT
1. Negative (-) battery cable.
2. Disable the SIR system.

CAUTION: Always use the correct fastener In the proper location. When you replace a fastener, use ONLY the exact part number for that application. The manufacturer will call out those fasteners that require a replacement after removal. The manufacturer will also call out the fasteners that require thread lockers or thread sealant. UNLESS OTHERWISE SPECIFIED, do not use supplemental coatings (paints, greases, or other corrosion Inhibitors) on threaded fasteners or fastener pint Interfaces. Generally, such coatings adversely affect the fastener torque and pint clamping force, and may damage the fastener. When you install fasteners, use the correct tightening sequence and specifications. Following these Instructions can help you avoid damage to parts and systems.

3. Lower or remove steering column from vehicle.
- Secure steering column to modular column holding fixture J 41352.

Modular Column Holding Fixture:

- Place holding fixture into vise.

Checking For Accident Damage:

Inspect
- Steering shaft assembly for accident damage.

4. Two pan head tapping screws (13) from lower shroud (28).
5. Lower shroud (28).
- Tilt shroud (28) down and slide back to disengage locking tabs.

Removing Lock Cylinder And Upper Shroud:

6. Two torx head screws (14) from upper shroud (10).
7. Lift upper shroud (10) to gain access to lock cylinder hole.
a. Hold key in "START" position.
b. Using 1/16-inch alien wrench push on lock cylinder retaining pin.
c. Release key to "RUN" position and pull steering column lock cylinder set (17) from lock module assembly (15).
d. Remove upper shroud (10).
8. Shift lever.
9. Shift lever seal (16).
10. Shroud protector (27) from lower shroud (28).

INSTALL OR CONNECT

CAUTION: Always use the correct fastener In the proper location. When you replace a fastener, use ONLY the exact part number for that application. The manufacturer will call out those fasteners that require a replacement after removal. The manufacturer will also call out the fasteners that require thread lockers or thread sealant. UNLESS OTHERWISE SPECIFIED, do not use supplemental coatings (paints, greases, or other corrosion Inhibitors) on threaded fasteners or fastener pint Interfaces. Generally, such coatings adversely affect the fastener torque and pint clamping force, and may damage the fastener. When you install fasteners, use the correct tightening sequence and specifications. Following these Instructions can help you avoid damage to parts and systems. Failure to do may result in component damage or malfunction of steering column.

1. Shift lever seal (16).
2. Shift lever.
3. Shroud protector (27) to lower shroud (28).
4. Move shift lever seal (16) and multi-function lever seal to ease in installation of upper and lower shrouds.
5. Upper shroud (10) and steering column lock cylinder set (17).
a. Key installed in lock cylinder (17) and in "RUN" position.

Sector And Lock Cylinder Alignment:

b. Ensure sector in lock module assembly (15) is in "RUN" position.
c. Lock cylinder (17) to upper shroud (10).
d. Line up locking tab and positioning tab with slots in lock module assembly (15) and push cylinder (17) into position. Two Torx head screws (14) to upper shroud (10).
- Tighten screws (14) to 1.4 Nm (12 lb in).
7. Lower shroud (28).
8. Ensure that slots on lower shroud (28) engage with tabs on upper shroud (10).
- Tilt lower shroud up and snap shrouds together.
- Two pan head tapping screws (13) to lower shroud (28).
- Tighten screws (13) to 6.0 Nm (53 lb in).
9. Shift lever seal (16) and multi-function lever seal into position.
10. Raise or install steering column to vehicle.
11. If all service operations are completed, enable the SIR system; refer to "ENABLING THE SIR SYSTEM."
12. Negative (-) battery cable.