AM/FM Stereo Radio (UM7 or UM6)

POWER (PWR) AND VOLUME CONTROL
The radio power switch is integral with the volume control. If the radio is OFF, rotating the volume control to the right will turn the system ON. If the radio is ON, rotating the volume control to the left will turn the system OFF. The ignition lock cylinder must be in the ACCESSORY or RUN position for the radio to operate.

BAND SWITCHING (AM/FM)
Depressing the tuning push-button will change the radio band between AM and FM.
When this push-button is depressed, the receiver will tune in the last frequency selected on the opposite band. The display will indicate the frequency and AM or FM mode.

TUNING (TUNE)
Rotating the TUNE push-button to the right will increase the AM or FM frequency.
Rotating it to the left will decrease the AM or FM frequency.

VOLUME (VOL)
Rotating the VOL push-button to the right will increase the volume. Rotating the VOL push-button to the left will decrease the volume.

TREBLE/BASS (TREB/BASS)
Slide the TREB lever up to increase the treble response. If the station is weak or noisy, slide the TREB lever down to reduce the noise.

Slide the BASS lever up to increase the bass response. Adjust the BASS lever to give a pleasing sound to your ear.

FADE AND BALANCE
The fade and balance function knobs adjust the relative volume between front and rear speakers and between left and right speakers, respectively. Rotating the appropriate end of either knob adjusts the relative volume.

Set (SET) Push-button (UM7) or Set/Eject (SET/EJECT) Push-button (UM6) Use the SET button in conjunction with the radio station preset pushbuttons to program radio frequencies into the memory locations. See "Radio Frequency Preset Pushbuttons" for instructions on pre setting radio stations. Radios equipped with cassette players combine the radio preset SET function with the cassette EJECT function.

RADIO FREQUENCY PRESET PUSHBUTTONS
Up to 14 stations can be preset into the radio's memory.

To preset 4 AM and 4 FM stations:
1. Tune in the desired station.
2. Press SET push-button. The SET indicator will light.
3. Press a station push-button. The SET indicator will go out. The radio will then tune in the selected station whenever that push-button is pressed.

If electrical power is interrupted (by a blown fuse, discharged battery, service procedure, etc.), the station(s) and time of day must be reset.

To preset 3 additional AM and 3 additional FM stations:
1. Tune in the desired station.
2. Press SET push-button. The SET indicator will light.

Engine Wiring To The Fuse Relay Center:

Engine Wiring:

Engine Wiring To A/C Compressor:

3. Press any two station pushbuttons at the same time. The station will return when the same two pushbuttons are pressed again.

RECALL (RCL)
If the radio is ON, pressing the volume control will alternately cause the display to change from time of day (TOD) to radio frequency display. Display the time with the ignition off by pressing the volume control knob.

SEEK (SEEK)
The 2000 Series radio is capable of seeking stations in forward and reverse directions. Push the button marked with the UP arrow. The radio will seek to the next station higher in frequency that has sufficient signal strength to be listenable. Push the button marked with the DOWN arrow.

The radio will seek to the next station lower in frequency that has sufficient strength to be listenable.

SCAN (SCAN) (UM7)
In the SCAN mode, each listenable station will be sampled for a few seconds. SCAN lights up in the display. SCAN is a two-button operation that requires the use of both SEEK pushbuttons.

To enter the SCAN mode, press and hold the SEEK up push-button, then press the SEEK push-button. The receiver will continue scanning each listenable station until you press the VOL control or press both SEEK pushbuttons again.

To SCAN down the dial, press and hold the pushbuttons in the opposite sequence.

PRESET SCAN (PSCAN) (UM7)
Any stations already stored on the preset pushbuttons can be sampled by the PSCAN mode. Press both

SEEK pushbuttons. The display shows PSCAN. It will scan each of the station presets (both FM1 and FM2) and stop for a few seconds or until you press either SEEK push-button or the RECALL knob again.

LOUDNESS
These units contain an auto-loudness feature. This feature boosts low-frequency audio response to compensate for the inability of the ear to hear low-level, low-frequency tones. This compensation varies inversely with the volume control setting. That is, at low volume settings, the low frequencies are boosted much more than at high volume settings.

CLOCK
To set the clock:
1. Press the SET push-button.
2. Within 5 seconds, press and hold the SEEK up push-button until the correct minute appears on the display.
3. Press and hold the SEEK down push-button until the correct hour appears on the display.