Correction
Have any of the following components had service recently?^ The theft deterrent module (This module is called the EVO/Passlock(TM) module in published service information.)
^ The ignition lock cylinder case assembly
^ The ignition switch
^ The PCM/VCM
If any of the above components have been replaced, the Passlock(TM) Learning procedure must be performed before any diagnostic procedures are performed. To assist in diagnosis, the following steps are provided.
1. Does the engine start? If not, use the Engine Cranks but Does Not Run diagnostic information in the Engine Controls sub-section of the applicable Service Manual.
2. Observe the Security indicator lamp in the instrument panel when you turn the key to the RUN position. Does the indicator lamp show any of the following conditions:
^ The lamp is On for five seconds, then goes Off. This is normal operation. The engine should start and run.
^ The lamp is On and does not go Off. This indicates a problem is detected but the engine starts. This indicates that the fault occurred when the engine was running.
^ The lamp flashes On and Off. This indicates a problem has been detected, this ignition cycle, by the Passlock system and the engine will not start.
^ The lamp does not come On. This is abnormal operation. Use the Security Indicator Inoperative diagnostic in the Theft Deterrent subsection of the applicable Service Manual.
Important:
You must diagnose the diagnostic trouble codes (DTCs) in the order specified in the DTC table shown. Failure to do so may result in one or more of the following conditions:
^ Extended diagnostic time
^ Incorrect diagnosis
^ Incorrect parts replacement
To assist in diagnosis/repair, the following step by step instructions are provided:
1. Install seat covers.
2. Connect the scan tool to the diagnostic link connector (DLC).
3. Enter scan tool diagnostics.
4. Select the model year of the vehicle.
5. Select light truck.
6. Select F1, (Body).
7. Select "C" or "K" for Series.
8. Select F2, (Passlock).
9. Select F0, (Diagnostic Trouble Codes (DTC)).
10. Select F0, (DTC information).
11. Select F0, (Current DTC).
12. Record on the repair order any current DTCs displayed. If none, skip the next step.
13. Is a current B2960 DTC displayed? If no, the condition is not present with this key cycle. Continue to the next step.
14. Select Exit.
15. Select F1, (History DTC).
16. Are any history DTCs other than B2960 present? If so, diagnose those DTCs first using the appropriate service information, otherwise continue.
17. Select Exit.
18. Select Exit.
19. Select F1, (Data Display).
20. Select F1, (Data).
21. Cycle the key to the OFF position and wait
20. seconds.
22. Slowly turn the key to the RUN position. Be careful not to turn the key into the START position.
23. Observe the following values:
^ Passlock(TM) Data Voltage should be 5.0 volts.
^ Passlock(TM) State should be Normal.
^ Passlock(TM) Code should be Open.
24. Rotate the key to the START position, and observe the following again:
^ Passlock(TM) Data Voltage should be less than 5.0 volts. Passlock(TM) Data Voltage should remain steady and not fluctuate. The test vehicle used for this diagnostic procedure had a voltage value of 2.49 volts. The vehicle being worked on may be either higher or lower than this value. The key is that it has to be less than 5.0 volts.
^ Passlock(TM) State should be "Monitor Pass lock(TM)".
^ Passlock(TM) Code should be Valid Code.
25. If no trouble is found and the customer has experienced one of the symptoms or the code is a history DTC, the most likely cause is the Passlock(TM) wiring, specifically the wires from the Passlock(TM) sensor to the Theft Deterrent module.
Caution:
This vehicle is equipped with a Supplemental Inflatable Restraint (SIR) System. Failure to follow the correct procedure could cause the following conditions:
25.1. Air bag deployment
25.2. Personal injury
25.3. Unnecessary SIR system repairs
26. In order to avoid the above conditions, observe the following guidelines.
27. Open the hood. Install fender covers.
28. Disconnect the negative battery cable.
29. Disable the SIR system using the following steps:
^ Turn the steering wheel so that the vehicle's wheels are pointing straight ahead.
^ Remove the key from the lock cylinder.
^ Remove the I/P cluster trim bezel by grasping the corners of the bezel and pulling the bezel rearward in order to disengage the retaining clips.
^ Remove the left sound insulator panel (if equipped), the knee bolster, and the knee bolster support.
^ Remove the connector position assurance (CPA) from the yellow 8-way connector, (C231) above (2) located at the bottom of the I/P just to the left of the steering column, and disconnect the connector. Remove the connector position assurance (CPA) from the yellow 4-way connector, (C232) above (7) located at the bottom of the I/P just to the left of the steering column, and disconnect the connector.
30 Cut and remove the wiring harness tie straps from the steering column wire harness (the lower one).
31. Remove the screw that retains connector C266 to the mounting bracket.
32. Loosen the screw holding the wiring harness connectors together at the connector C266 (2) and separate the connection.
33. Separate the turn signal and multifunction switch harness (2) from the 18-way connector (1). They have a locking tab in the center of each connector that needs to be released.
Important:
For all vehicles, use either the correct mating terminal, or electrical tool GM # 12094430, (J 38125-11A) (Blue) from the J 38125-B Terminal Repair kit. Perform a pull test to determine if the terminals have proper tension. If one is found where the tension is suspect, replace the terminal.
34. Circuit number 1057, Orange with Black stripe wire, in cavity C4.
Circuit number 812, Red with White stripe wire, in cavity B1.
Circuit number 1836, Yellow wire, in cavity D3.
35. On the end of the 18-way connector is the date the ignition switch wiring harness was manufactured. This date is etched in the plastic of the connector. If is displayed as two lines of numbers (ie: GM XXX, XXXX). The bottom row of four digits are the digits that must be verified. Do not be confused by the single row of four digits on one end of the connector. These four digits are the connector part number. If two rows are not found, the following procedure must be performed. The following defines the four digits:
^ Month (1) Alpha/Numeric Character (1 = January, 4 = April, 9 = September, 0 = October, N = November, etc.)
^ Day (2) numbers (01-31)
^ Year (1) Number (9 = 1999, 0 = 2000)
36. If the date code is less than N080, (November 08, 2000), place a drop of solder to the wire and terminal interfaces on the wires in the following cavities:
^ Circuit number 1057, Orange/Black wire in cavity C4
^ Circuit number 812, Red/White wire in cavity B1
^ Circuit number 1836, Yellow wire in cavity D3
37. Reconnect the turn signal and multifunction switch harness (2) from the 18-way connector (1).
Important:
Connector bolt torque is critical. Tightening the bolt to 7 Nm (61 lb in) may cause the pal nut of the connector to strip. Tightening the bolt less than 4 Nm (35 lb in) may result in an intermittent connection.
38. Connect the 48-way connector (C266) to the vehicle's wiring harness. Tighten the screw holding the wiring harness connectors together.
Tighten
Tighten the retaining screw to 6 Nm (53 lb in).
39. Cycle the steering column tilt from full up to full down a minimum of ten times.
40. Squeeze the ends of connector C266 together with your fingers, forcing the terminals and connector to properly seat together.
41. Recheck the retaining screw for connector C266 torque.
Tighten
Tighten the retaining screw holding the wiring harness connectors together to 6 Nm (53 lb in).
42. Again, cycle the steering column tilt from full up to full down a minimum of ten times.
43. Again, squeeze the ends of connector C266 together with your fingers, forcing the terminals and connector to properly seat together.
44. Recheck the retaining screw for connector C266 torque.
Tighten
Tighten the retaining screw holding the wiring harness connectors together to 6 Nm (53 lb in).
45. Again, cycle the steering column tilt from full up to full down a minimum of ten times.
46. Again, squeeze the ends of connector C266 together with your fingers, forcing the terminals and connector to properly seat together.
47. Recheck the retaining screw for connector C266 torque.
Tighten
Tighten the retaining screw holding the wiring harness connectors together to 6 Nm (53 lb in).
48. Install the knee bolster support to the IP.
^ Connect the lap cooler hose to the knee bolster.
^ Connect the brake release cable to the park brake assembly.
^ Snap the knee bolster into the I/P assembly.
^ Install the knee bolster screws.
Tighten
Tighten the screws to 2 Nm (18 lb in).
49. Connect the headlight switch wiring connectors to the I/P bezel and install the bezel.
50. Connect the yellow 4-way connector C232 (7) and install the CPA.
51. Connect the yellow B-way connector C231 (2) and install the CPA.
52. Connect the negative battery cable.
53. Observe the Security indicator lamp when the key is turned to the RUN position. The Security lamp should come On for five seconds, then go Off. If it doesn't, you must recheck your work.
54. Observe the SIR lamp. The lamp should be Off.
55. Remove the fender covers and close the hood.
56. Remove the seat covers.