a. Transmission Disassemble
DISASSEMBLY PROCEDUREFor component locations, refer to Exploded Views.
^ Tools Required
- J 38805 Output Shaft Nut Socket
1. Remove the shift tower to the shift cover bolts.
2. Remove the shift tower from the shift cover.
3. Remove the shift tower isolator plate from the shift cover.
4. Remove the shift cover to the transmission case bolts. Pry the cover off by inserting screwdrivers in the slots provided.
5. (RWD P-models) Shift the transmission into two gears in order to lock the output shaft.
IMPORTANT:
^ Do not pry apart on the mating surfaces. The mating surfaces may be damaged.
^ Do not disassemble the shift cover. Individual components of the shift cover are not serviced. A damaged or worn shift cover must be replaced as a complete assembly.
6. (RWD P-models) Remove the following parts:
6.1. The mainshaft nut
6.2. The washer
6.3. The spline seal
7. (RWD C-models) Remove the following parts:
7.1. The mainshaft nut
7.2. The washer
7.3. The yoke assembly
8. (4WD models) Remove the rear oil retainer bolts. Strike the housing lightly with a soft-faced hammer. Pry off the housing.
9. (RWD models) Remove the rear oil retainer bolts. Strike the housing lightly with a soft-faced hammer. Pry off the housing.
10. (4WD models) Shift the transmission into two gears in order to lock the output shaft.
11. (4WD models) Remove the mainshaft nut and the washer. Use the J 38805.
12. (4WD models) Remove the vibration damper. Use a suitable gear puller.
13. Mark the main drive gear bearing retainer and the case for alignment. Remove the main drive gear bearing retainer bolts. Drive out the bearing retainer from the transmission case. Use a brass punch.
14. Remove the main drive gear and the main drive gear bearing.
15. Support the 5TH gear shift fork. Drive out the 5TH gear shift fork roll pins.
16. Remove the 5TH gear clutch gear retainer ring.
17. Scribe a mark on the overdrive synchronizer hub and on the sleeve. This will help you to replace the parts in the same position.
18. Remove the following parts:
18.1. The countershaft overdrive gear and the shift fork as an assembly (Do not let the synchronizer come apart. If necessary, remove the clutch gear, the synchronizer ring, the spacer, and the bearings. The overdrive gear will drop down for easy removal.)
18.2. The countershaft thrust washer
18.3. The pin
19. (RWD models) Remove the mainshaft 5TH gear and the vehicle speed sensor reluctor wheel.
20. Remove the following parts:
20.1. The mainshaft rear bearing retaining plate bolts.
20.2. The bearing retainer plate
20.3. The shim(s)
20.4. The mainshaft rear bearing cup (Move the synchronizer sleeves into neutral position. Raise the fifth gear shift lever up out of the way and hold with a rubber band.)
21. Remove the mainshaft assembly as follows:
21.1. Move the synchronizer sleeves into neutral position.
21.2. Raise the 5TH gear shift lever up out of the way. Secure the lever with a rubber band.
21.3. Lift the mainshaft assembly by the nose through the front of the case. You may have to wiggle and twist the mainshaft assembly in order to disengage the second speed gear from the countershaft.
21.4. Remove the mainshaft assembly from the transmission case.
22. Remove the following parts:
22.1. The countershaft bearing retaining plate bolts
22.2. The bearing retainer plate
22.3. The shim(s)
22.4. The countershaft rear bearing cup
23. Remove the following parts:
23.1. The reverse idler gear shaft (Push the reverse idler shaft out from inside the transmission case.)
23.2. The reverse idler gear
23.3. The washers
23.4. The bearings
23.5. The spacer
24. Remove the countershaft rear bearing. Use a suitable bearing puller. Position the bearing puller behind the bearing inner race.
25. Remove the countershaft assembly from the transmission case.
26. Remove the countershaft bearing cap and the front bearing cup.
27. Drive out the roll pin from the 5TH gear shift lever. Remove the shift lever shaft. Push the shaft outward from inside the case. Remove the 5TH gear shift lever from the shift lever shaft.