(UM7)

CLOCK
In order to set the clock, perform the following steps:
1. Press the SET push button.
2. Within 5 seconds, press and hold the SEEK right arrow key until the correct minute appears on the display.
3. In order to set the hour, press and hold the SEEK left arrow key until the correct hour appears on the display.

VOLUME (VOLUME)
^ The radio power switch is the same knob as the volume control. Use the radio power switch/volume control knob in order to turn the system ON and OFF and in order to control the volume.
^ In order to increase the volume and in order to turn the radio ON, turn the knob clockwise.
^ In order to decrease the volume or in order to turn the radio OFF, turn the knob counterclockwise.
^ The ignition lock cylinder must be in the ACCESSORY or the RUN position in order for the radio to operate.

RECALL (RECALL)
^ Press the volume control push button in order to alternately cause the display to change from the time of day (TOD) to the radio frequency display when the radio is ON.
^ Press the volume control knob in order to display the TOD with the ignition OFF.

BAND SWITCHING (AM/FM)
^ Depress the lower knob in order to change the radio band between AM and FM.
^ Depress the lower knob in order to tune into the last frequency selected on the opposite band. The display will indicate the frequency and AM or FM mode.

TUNING (TUNE)
^ Rotate the TUNE knob clockwise in order to increase the AM or FM frequency.
^ Rotate the TUNE knob counterclockwise in order to decrease the AM or FM frequency.

TREBLE/BASS (TREB/BASS)
^ Slide the TREB level up in order to increase the treble response.
^ Slide the TREB lever down in order to reduce the noise if the station is weak or noisy.
^ Slide the BASS lever up in order to increase the bass response.
Adjust the BASS lever in order to create a pleasing sound to your ear.

BALANCE (BAL)
^ Turn the control behind the upper knob in order to move the sound to the left or the right speakers.
^ Use the middle position in order to balance the sound between the speakers.

FADE (FADE)
^ Turn the control behind the lower knob in order to move the sound to the front or the rear speakers.
^ Use the middle position in order to balance the sound between the speakers.

SEEK (SEEK)
1. Press the right arrow button in order to tune into the next station higher in frequency that has sufficient signal strength to be listenable.
2. Press the left arrow button in order to tune into the next station lower in frequency that has sufficient strength to be listenable.

SCAN (SCAN)
1. Press both SEEK buttons in order to listen to a few seconds of each radio station. SCAN will light up on the display.
2. Press the right arrow button in order to tune into the next higher station
3. Press the left arrow button in order to tune into the next lower station.
4. Press VOLUME or both SEEK buttons in order to stop scanning.

SET (SET) PUSH BUTTON
Use the SET button along with the radio station preset push buttons in order to program the radio frequencies into the memory locations. Refer to Radio Frequency Preset Pushbuttons for instructions on presetting radio stations.

RADIO FREQUENCY PRESET PUSH BUTTONS
Up to 14 stations can be preset into the radio's memory. In order to preset 4 AM and 4 FM stations, perform the following steps:
1. Tune into the desired radio station.
2. Press the SET push button. SET will appear on the display.
3. Press any station push button.
The SET on the display will go out. The radio will then tune into the selected station whenever that push-button is pressed.
4. If electrical power is interrupted (by a open fuse, discharged battery, service procedure, etc.), the station(s) and time of day must be reset.

In order to preset 3 additional AM, FM1, and FM2 stations, perform the following steps:
1. Tune into the desired radio station.
2. Press the SET push-button. SET will appear on the display.




Press any 2 adjacent station push buttons at the same time.
The SET on the display will go out. The station will return when the same two push buttons are pressed again.

LOUDNESS
The UM7 stereos contain an auto-loudness feature.

The auto-loudness feature boosts low-frequency audio response to compensate for the inability of the ear to hear low-level, low-frequency tones.

This compensation varies inversely with the volume control setting.

That is, at low volume settings, the low frequencies are boosted much more than at high volume settings.