(UM6)

CLOCK
In order to set the clock, perform the following steps:
1. Press the SET push button.
2. Within 5 seconds, press and hold the SEEK right arrow key until the correct minute appears on the display.
3. In order to set the hour, press and hold the SEEK left arrow key until the correct hour appears on the display.

VOLUME (VOLUME)
- The radio power switch is integral with the volume control.
- Use the radio power switch/volume control knob in order to turn the system ON and OFF.
- Use the radio power switch in order to control the volume.
- The ignition lock cylinder must be in the ACCESSORY or RUN position in order for the radio to operate.
- Turn the radio power switch clockwise in order to turn the system ON.
- Turn the radio power switch clockwise in order to increase the volume.
- Turn the radio power switch counterclockwise in order to turn the system OFF.
- Turn the radio power switch counterclockwise in order to decrease the volume.

RECALL (RECALL)
- Press the volume control push button in order to alternately cause the display to change from the time of day (TOD) to the radio frequency display. The radio must be turned ON in order to perform the RECALL procedure.
- Press the volume control knob in order to display the time of day while the radio is turned OFF.

BAND SWITCHING (AM/FM)
Press the lower knob in order to switch between AM, FM1, and FM2. The display indicates the current band.

TUNING (TUNE)
- Rotate the TUNE knob clockwise in order to increase the AM or FM frequency.
- Rotate the TUNE knob counterclockwise in order to decrease the AM or FM frequency.

TREBLE/BASS (TREB/BASS)
- Slide the TREB lever up in order to increase the treble response.
- Slide the TREB lever down in order to reduce noise if the station is weak or noisy.
- Slide the BASS lever up in order to increase the bass response
- Adjust the BASS lever in order to create a pleasing sound to your ear.

BALANCE (BAL)
- Turn the control behind the upper knob in order to move the sound to the left or the right speakers
- Use the middle position in order to balance the sound between the speakers.

FADE (FADE)
- Turn the control behind the lower knob in order to move the sound to the front or rear speakers.
- Use the middle position in order to balance the sound between the speakers.

SEEK (SEEK)
1. Press the right arrow button in order to tune into the next station higher in frequency.
2. Press the left arrow button in order to tune into the next station lower in frequency.

In order to tune into a radio station of higher or lower frequency, the station must have sufficient strength in order for the station to be listenable.

SET/Elect (SET/EJECT) Push buttons
Use the SET/EJECT button along with the radio station preset push buttons in order to program the radio frequencies into the memory locations. Refer to Radio Frequency Preset Push buttons for instructions on presetting radio stations.

RADIO FREQUENCY PRESET PUSH BUTTONS
1. Up to 21 stations (7AM, 7 FM1, and 7 FM2 stations) can be preset into the radio's memory.
2. In order to preset 4 AM, 4 FM1, and 4 FM2 stations, perform the following steps:
2.1. Tune into the desired radio station
2.2. Press the SET push button.
Set will appear on the display.
2.3. Press a station push button.
The SET on the display will go out. The radio will then tune into the selected station whenever that push button is pressed.

1. If electrical power is interrupted (by an open fuse, discharged battery, service procedure, etc.), the station(s) and time of day must be reset.
2. In order to preset 3 additional AM, FM1, and FM2 stations, perform the following steps:
2.1. Tune into the desired radio station.
2.2. Press the SET push button. SET will appear on the display.
2.3. Press any 2 station adjacent push buttons at the same time.
The SET on the display will go out.
The station will return when the same 2 push buttons are pressed again.

PRESET SCAN (PSCAN)
Any stations already stored on the preset push buttons can be sampled by the PSCAN mode.
1. In order to use PSCAN, press both SEEK push buttons in order to scan through each of the preset stations.
The system will scan through and play each preset station for a few seconds.
2. Press either SEEK or RECALL in order to stop scanning through the preset stations.

LOUDNESS
The auto-loudness feature boosts low-frequency audio response in order to compensate for the inability of the ear to hear low-level, low-frequency tones.

The auto-loudness compensation varies inversely with the volume control setting.

At low volume settings, the low frequencies are boosted much more than at high volume settings.

CASSETTE TAPE PLAYER
1. In order to play a tape, the ignition lock cylinder must be in the ACCESSORY or RUN position and the receiver must be turned ON.
Tapes are end-loaded into the cassette player.
2. Insert the tape squarely through the door, exposed tape side of the cassette facing to the right.
3. When the tape is fully inserted, the AM/FM portion of the radio will turn off and the tape will begin playing.
4. The tape players works best with tapes that are 30-45 minutes long on each side. Longer running tapes may not work well in these players because they are usually too thin.
5. Once the tape is playing, use the upper and lower knobs for the volume, the balance and the fade just as with the radio.
An arrow indicates which side of the tape is being played.
6. Press the SEEK right arrow key in order to fast forward the tape.
The tape will advance rapidly until the SEEK left arrow is pressed.
7. Press the SEEK left arrow key in order to rewind the tape.
The tape will rewind rapidly until the SEEK right arrow is pressed.
8. Press the upper knob in order or to go from one side of the tape to the other.
9. Press the EJECT push button in order to remove the tape or in order to stop the tape and switch to the radio.