a. Transmission Disassemble
Transmission Disassembly^ Tools Required
^ J 21427-01 Speedometer Gear Puller Adapter
^ J 23907 Slide Hammer
^ J 24420-B Gear Puller
^ J 26941 Output Shaft Oil Seal Remover
^ J 3289-20 Base Holding Fixture
^ J 36509 Shift Shaft Detent Plug Remover
^ J 36515 Assembly Pallet
^ J 36515-15 Mainshaft Adapter
^ J 36515-16 Countershaft Adapter
^ J 36824 Transmission Adapters
^ J 8763-02 Holding Fixture C-Clamp
^ J 8763-21 Balance Bracket for C-Clamp
1. Remove 2 reverse idler shaft support bolts.
2. Remove 2 lower-housing bolts. Tool J 3289-20 must be mounted securely on a sturdy workbench.
3. Assemble the transmission holding fixture:
3.1. The J 8763-21 onto the J 8763-02
3.2. The J 36824 onto the transmission housing
3.3. The J 8763-02 onto the J 36824
3.4. The J 8763-02 onto the J 3289-20
4. Remove the backup lamp switch assembly.
5. Remove the shift shaft block-out bushing pin.
6. Remove the following components:
6.1. The bolt
6.2. The vehicle speed sensor
7. Complete the following tasks:
7.1. Remove the detent plug. Use the J 36509 and the J23907.
7.2. Remove the detent spring and the detent plunger.
8. Remove the concentric slave cylinder.
9. Position the transmission vertically. Scribe the retainer and the case to aid in ensuring proper position during reassembly. Remove the following components:
9.1. The 6 bolts
9.2. The input shaft bearing retainer
10. Remove the retainer by screwing two of the removed bolts into the threaded holes provided. Press off the retainer.
11. Tap the clutch release bearing pilot with a rubber mallet.
12. Remove the input shaft snap ring.
13. Position the transmission horizontally. Remove the front housing to the rear housing bolts.
Important: Support the front housing. Do not allow the front housing to fall.
14. Drive the 2 dowel pins into the front housing.
15. Remove the front housing.
16. Remove the countershaft bearing.
17. Remove the reverse idler shaft support. The idler shaft support will snap out.
18. Move all of the shift forks forward. Engage the 4th gear, the 2nd gear, and Reverse gear. Retain the shift lever detent plunger and spring.
19. Remove the shift shaft lever roll pin.
19.1. Rotate the shift shaft lever finger down.
19.2. Support the shift shaft end.
19.3. Drive out the roll pin.
19.4. Ensure that the roll pin clears the 2nd speed gear.
20. Shift all of the gears into neutral.
21. Engage the 5th speed gear.
Notice: Excessive force peens the shift shaft and damages the shift shaft bearing. This causes increased shift effort.
22. Push the shift shaft into the housing.
23. Remove the shift shaft socket roll pin.
23.1. Rotate the input shaft until a gap in the 5th speed/reverse speed synchronizer hub is directly under the roll pin.
23.2. Support the shift shaft end.
23.3. Drive out the roll pin. Use a 5 mm (3/16 inch) punch. The roll pin will fall into the transmission housing.
24. Remove the following components:
24.1. The shift shaft
24.2. The shift shaft socket
24.3. The shift shaft lever
24.4. The shift shaft block-out bushing
25. Remove the 3rd/4th speed gear shift fork. Rotate counter clockwise
26. Loosen 3 bolts on the rear of the housing. Do not remove the bolts.
27. Install the tool J 36515-15 on the input shaft.
28. Install the tool J 36515-16 on the countershaft.
29. Install the tool J 36515 to the transmission assembly.
30. Place the unit fixture on the bench while holding the J 36515 fixture assembly on the transmission assembly.
31. Remove tools J 8763-02 and J 36824 from the transmission housing.
32. Remove the 3 bolts from the rear housing.
33. Remove the rear housing. Tap the rear housing with a rubber mallet.
34. Remove the mainshaft bearing retainer.
35. Remove the following components:
35.1. 2 shift forks (1)
35.2. The reverse idler gear (2)
36. Partially lift the mainshaft to allow removal of the countershaft. Remove the following components:
36.1. The countershaft (3)
36.2. The countershaft bearing (4)
37. Remove the vehicle speed sensor reluctor wheel. Use the J 21427-01 and the J 24420-B. Discard the reluctor wheel.
38. Remove the following components:
^ The rear mainshaft bearing snap ring (1)
^ The rear mainshaft bearing (2)
39. Remove the mainshaft assembly from the assembly pallet J 3655. Remove the following parts:
^ The input shaft
^ The mainshaft pilot bearing from the input shaft