Tie Rod: Service and Repair
Tie Rod Replacement - InnerTools Required
^ J34028 Inner Tie Rod Wrench
Removal Procedure
Important: The boot and retaining clamps must be replaced when replacing the inner tie rod.
1. Remove the rack and pinion boot.
2. Place the gear in a vise.
Important: Do not change the steering gear preload adjustment before moving the inner tie rod from the steering gear. This could result in damage to both the pinion and the steering gear.
3. Separate the shock dampener (4) from inner tie rod assembly (2).
4. Slide the shock dampener back on the rack (3).
Important: The pipe wrench must be placed at the valve end of the steering gear (1) and positioned up against the inner tie rod housing. Placing the pipe wrench in any other location will cause damage to the steering gear (1).
5. Place a pipe wrench on the rack (3) next to the inner tie rod housing (2).
6. Place a wrench on the flats of the inner tie rod housing (2).
7. Rotate the inner tie rod housing (2) counterclockwise until the inner tie rod separates from the rack (3).
8. At the other gear end, separate the shock dampener (3) from inner tie rod assembly (2).
9. Slide the shock dampener (3) back on the rack (4).
Important: The pipe wrench must be placed at the valve end of the steering gear (5). Placing the pipe wrench in any other location will cause damage to the steering gear (5).
10. Maintain the pipe wrench on the opposite end of the rack (6).
11. Place a wrench on the flats of the inner tie rod housing (2).
12. Rotate the inner tie rod housing (2) counterclockwise until the inner tie rod separates from the rack (4).
13. Remove old LOCTITE from the threads (1) of the rack (3) and inner tie rod (2).
Installation Procedure
1. Slide the shock dampener (4) forward onto the rack (3).
Important: Threads must be clean prior to LOCTITE application. Check the LOCTITE (or equivalent) container expiration date. Use only enough LOCTITE. to evenly coat threads.
2. Apply LOCTITE 262 (or equivalent) to the inner tie rod threads (2).
3. Attach the inner tie rod (2) onto the rack (3).
4. Place a pipe wrench on the rack (3) next to the inner tie rod housing (2).
Notice: Refer to Fastener Notice in Service Precautions.
Important: The pipe wrench must be placed at the valve end of the steering gear (1) and positioned up against the inner tie rod housing. Placing the pipe wrench in any other location will cause damage to the steering gear (1).
5. Place a torque wrench and J34028 on the flats of the inner tie rod housing (2).
Tighten the inner tie rod housing to 100 Nm (74 ft. lbs.).
6. Slide the shock dampener (1) over the inner tie rod housing (2) until the front lip of the shock dampener (1) bottoms against the inner tie rod housing (2).
7. Slide the shock dampener (3) forward onto the rack (2).
Important: Threads must be clean prior to LOCTITE application. Check the LOCTITE (or equivalent) container expiration date. Use only enough LOCTITE to evenly coat threads.
8. Apply LOCTITE 262 (or equivalent) to the inner tie rod (1) threads.
9. Attach the inner tie rod (1) onto the rack (2).
Important: The pipe wrench must be placed at the valve end of the steering gear (5) and positioned up against the inner tie rod housing. Placing the pipe wrench in any other location will cause damage to the steering gear (5).
10. Maintain the pipe wrench on the opposite end of the rack (5) next to the inner tie rod housing.
11. Place a torque wrench and J34028 on the flats of the inner tie rod housing (1).
Tighten the inner tie rod housing to 100 Nm (74 ft. lbs.).
12. Slide the shock dampener (1) over the inner tie rod housing (2) until the front lip of the shock dampener (1) bottoms against the inner tie rod housing (2).
13. Remove the gear from the vise.
14. Install the rack and pinion boot.