Instrument Cluster

INSTRUMENT PANEL CLUSTER (IPC) DESCRIPTION AND OPERATION

DISPLAYS TEST
Certain instrument panel cluster (IPC) features are tested when the ignition is turned on in order to verify the features are working properly. The following indicators illuminate for 3 seconds:
- The antilock brake system (ABS) indicator
- The brake indicator
- The park brake indicator
- The SECURITY indicator
- The upshift indicator
- All gages sweep to their minimum physical position and then to their actual physical position.

The following indicators illuminate for the specified times:
- The AIR BAG indicator flashes 7 times.
- The seatbelt indicator illuminates for 20 seconds followed by 55 seconds of flashing with the drivers seatbelt unfastened, or, the seatbelt indicator will illuminate for 8 seconds with the drivers seatbelt fastened.
- All message center segments illuminate briefly.

INDICATORS AND WARNING MESSAGES
Refer to Indicator/Warning Message Description and Operation.

ENGINE COOLANT TEMPERATURE GAGE
The IPC displays the engine coolant temperature as determined by the powertrain control module (PCM). The IPC receives a class 2 message from the PCM indicating the engine coolant temperature. The engine coolant temperature gage defaults to 100°F (40°C) or below if:
- The PCM detects a malfunction in the engine coolant temperature sensor circuit.
- The IPC detects a loss of class 2 communications with the PCM.

ENGINE OIL PRESSURE GAGE
The IPC displays the engine oil pressure as determined by the PCM. The IPC receives a class 2 message from the PCM indicating the engine oil pressure. The engine oil pressure gage defaults to 0 psi (0 kPa) or below if:
- The PCM detects a malfunction in the engine oil pressure (EOP) sensor circuit.
- The IPC detects a loss of class 2 communications with the PCM.

FUEL GAGE
The IPC displays the fuel level as determined by the PCM. The IPC receives a class 2 message from the PCM indicating the fuel level percent. The fuel gage defaults to empty if:
- The PCM detects a malfunction in the fuel level sensor circuit.
- The IPC detects a loss of class 2 communications with the PCM.

When the fuel level is less than a pre-determined value, the IPC illuminates the low fuel indicator.

ODOMETER
The base IPC contains a season odometer and a trip odometer. The up level IPC contains a season odometer and 2 trip odometers. Momentarily press the trip/reset switch on the IPC in order to toggle between the season odometer and the trip odometer. Press the trip/reset switch for greater than 2 seconds, while the trip odometer is displayed, in order to reset the trip odometer.

The IPC calculates the mileage based on the vehicle speed signal circuit from the PCM. The odometer will display 'error' if an internal IPC memory failure is detected. The odometer displays either miles or kilometers as requested by the activation of the Personalization button on the steering wheel controls.

PRND321 DISPLAY
The IPC displays the selected gear position as determined by the PCM. The IPC receives a class 2 message from the PCM indicating the gear position. The PRND321 display blanks if:
- The PCM detects a malfunction in the transmission range switch circuit.
- The IPC detects a loss of class 2 communications with the PCM.

SPEEDOMETER
The IPC displays the vehicle speed based on the information from the PCM. The PCM converts the data from the vehicle speed sensor to a 4000 pulses/mile signal. The IPC receives a class 2 message from the PCM indicating the vehicle speed.

TACHOMETER
The IPC displays the engine speed based on the information from the PCM. The PCM converts the data from the engine speed sensor to a 2 pulses/engine revolution signal. The IPC receives a class 2 message from the PCM indicating the engine speed.

VOLTMETER
The IPC displays the vehicle voltage based on the information from the body control module (BCM). The IPC uses class 2 serial data information from the BCM to provide a voltage level indication on the voltmeter.