Scan Tool Data Definitions
SCAN TOOL DATA DEFINITIONS
8 Digit GM Part Number: The scan tool displays the eight digit part number of the module selected.
Base Model Part Number: The scan tool displays the eight digit base part number of the lift gate module.
Battery Voltage: The scan tool displays 9.0-15.0 volts. The state of the battery voltage supplied to the module selected.
Boot S/W Part No.: The scan tool displays the eight digit boot software part number of the lift gate module.
Boot S/W Suffix: The scan tool displays the two digit suffix number of the lift gate module boot software.
Calibration S/W Part No.: The scan tool displays the eight digit calibration software part number of the lift gate module.
Calibration S/W Suffix: The scan tool displays the two digit suffix number of the lift gate module calibration software.
Current Power Mode: The scan tool displays Off Awake/Retained Accessory Power/Accessory/Run/Crank. The ignition switch input states to the EGM used for power moding.
Drop Latch Switch: The scan tool displays Active/Inactive. The endgate drop latch switch input to the EGM, where a switch transition is displayed as Active.
Endgate Key Cylinder: The scan tool displays Idle/Close/Open. The endgate key cylinder switch input to the EGM, where a switch transition is displayed as either Close or Open.
Endgate Window Pos. 1: The scan tool displays Counts. The endgate window hall effect sensor input to the EGM displayed in counts.
Endgate Window Pos. 2: The scan tool displays Counts. The endgate window hall effect sensor input to the EGM displayed in counts.
Ign. Since Current DTC: The scan tool displays Cycles. The number of ignition switch cycles since the last DTC was set.
Julian Date of Build: The scan tool displays the four digit date of the module selected build.
Learned Window Closed Position: The scan tool displays Counts. The endgate window closed position input to the EGM displayed in counts.
Learned Window Open Position: The scan tool displays Counts. The endgate window open position input to the EGM displayed in counts.
Left Lower Latch: The scan tool displays Active/Inactive. The endgate lower left latch motor output from the EGM, where a latch motor transition to open is displayed as Active.
Left Upper Latch: The scan tool displays Active/Inactive. The endgate upper left latch motor output from the EGM, where a latch motor transition to open is displayed as Active.
Liftgate Ajar Switch: The scan tool displays Closed/Ajar. The liftgate ajar switch input to the LGM, where an open lift gate is displayed as Ajar.
Liftgate Unlock Switch: The scan tool displays Active/Inactive. The liftgate unlock switch input to the LGM.
Liftglass Ajar Switch: The scan tool displays Closed/Ajar. The liftglass ajar switch input to the LGM, where an open liftglass is displayed as Ajar.
Lock Command: The scan tool displays Unlock/Lock. The virtual state of the endgate or liftgate latch motors.
Lower Left Ajar Switch: The scan tool displays Closed/Ajar. The endgate lower left ajar switch input to the EGM, where an open lower left latch motor is displayed as Ajar.
Operational S/W Part No.: The scan tool displays the eight digit operational software part number of the lift gate module.
Operational S/W Suffix: The scan tool displays the two digit suffix number of the lift gate module operational software.
Rear Gate/Door: The scan tool displays Open/Closed. The scan tool displays the status of the rear gate/door.
Requested Lock/Unlock: The scan tool displays Idle/Lock/Unlock. The liftgate unlock switch input to the LGM.
Right Upper Latch: The scan tool displays Active/Inactive. The endgate upper right latch motor output from the EGM, where a latch motor transition to open is displayed as Active.
Software Part Number: The scan tool displays the eight digit part number of the end gate module software.
Software Revision Number: The scan tool displays the two digit revision number of the end gate module software.
Swing Latch Switch: The scan tool displays Active/Inactive. The endgate swing latch switch input to the EGM, where a switch transition is displayed as Active.
Upper Left Ajar Switch: The scan tool displays Closed/Ajar. The endgate upper left ajar switch input to the EGM, where an open upper left latch motor is displayed as Ajar.
Upper Right Ajar Switch: The scan tool displays Closed/Ajar. The endgate upper right ajar switch input to the EGM, where an open upper right latch motor is displayed as Ajar.
Window Motor: The scan tool displays Idle/Up/Down. The state of the window motor output from the EGM.
Year Module Built: The scan tool displays the four digit date of the year the module selected was built.