Rack and Pinion Inner Tie Rod Replacement - Off Vehicle (Magnasteer)
Rack and Pinion Inner Tie Rod Replacement - Off Vehicle (Magnasteer)
^ Tools Required
- J 34028 Inner Tie Rod Wrench
Disassembly Procedure
1. To remove the rack and pinion boot, refer to Rack and Pinion Boot and Breather Tube Replacement - Off Vehicle.
2. Place the gear in a vise.
3. Remove the shock dampener (6) from the inner tie rod housing (4).
Notice: Do not change the steering gear preload adjustment before moving the inner tie rod from the steering gear. Changing the steering gear preload adjustment before moving the inner tie rod could result in damage to the pinion and the steering gear.
4. Slide the shock dampener (6) back on the rack (5).
5. Place a pipe wrench on the rack (5) next to the inner tie rod housing (4).
Notice: The pipe wrench must be placed at the valve end of the steering gear and positioned up against the inner tie rod housing. Placing the pipe wrench in any other location will cause damage to the steering gear.
6. Place a wrench on the flats of the inner tie rod housing (4).
7. Rotate the inner tie rod housing (4) counterclockwise, while holding the rack stationary, until the inner tie rod separates from the rack (5).
8. Remove the shock dampener (3) from the inner tie rod housing (2).
9. Slide the shock dampener (3) back on the rack (5).
10. Place a pipe wrench on the rack.
Notice: Refer to Pipe Wrench Positioning Notice in Service Precautions.
11. Place a wrench on the flats of the inner tie rod housing (2).
12. Rotate the inner tie rod housing (2) counterclockwise, while holding the rack stationary, until the inner tie rod (1) separates from the rack (5).
13. If female rack (1) and male inner tie rod (3), remove the old LOCTITE from the threads (2) of the inner tie rod (3) and the rack (1). If male rack (5) and female inner tie rod (4) LOCTITE will not be present.
Assembly Procedure
1. Slide the shock dampener (4) forward onto the rack (3).
2. If male rack (3) and female inner tie rod (2) do not apply LOCTITE.
If female rack (3) and male inner tie rod (2), apply LOCTITE 262, or equivalent, to the inner tie rod threads.
Important: Threads must be clean prior to LOCTITE application. Check LOCTITE, or equivalent, container for expiration date. Use only enough LOCTITE to evenly coat threads.
3. Attach the inner tie rod onto the rack (3).
4. Place a pipe wrench on the rack (3) next to the inner tie rod housing (2).
Notice: Refer to Pipe Wrench Positioning Notice in Cautions and Notices.
5. Place a torque wrench and J 34028 on the flats of the inner tie rod housing (2).
^ Tighten the inner tie rod to 100 Nm (74 ft. lbs.).
Notice: Refer to Fastener Notice in Service Precautions.
6. Slide the shock dampener (2) forward onto the rack.
7. If male rack and female inner tie rod (1) do not apply LOCTITE.
If female rack and male inner tie rod (1), apply LOCTITE 262, or equivalent, to the inner tie rod threads.
Important: Threads must be clean prior to LOCTITE application. Check LOCTITE, or equivalent, container for expiration date. Use only enough LOCTITE to evenly coat threads.
8. Attach the inner tie rod (1) onto the rack.
9. Place a pipe wrench on the rack next to the inner tie rod housing (4).
Notice: Refer to Pipe Wrench Positioning Notice in Service Precautions.
10. Place a torque wrench and J 34028 on the flats of the inner tie rod housing (7).
^ Tighten the inner tie rod to 100 Nm (74 ft. lbs.).
11. Place the inner tie rod assembly (2) in a vise.
12. Stake both sides of the female inner tie rod assembly housing to the male rack (1).
Important: If female rack (1) and male inner tie rod (2) do not stake. If male rack (1) and female inner tie rod (2) you must stake.
13. Insert a 0.25 mm gage (1) between the rack (2) and the inner tie rod housing in order to check both stakes. The feeler gage (1) must not pass between the rack and the housing stake.
14. Slide the shock dampener (2) over the inner tie rod housing (3) until the front lip of the shock dampener (2) bottoms against the inner tie rod housing (3).
15. To assemble the rack and pinion boot.