Scan Tool Data Definitions 1

SCAN TOOL DATA DEFINITIONS

The Engine Control Module Scan Tool Data Definitions contains a brief description of all engine control module (ECM) related parameters available on the scan tool. The list is arranged in alphabetical order. A given parameter may appear in any one of the data lists. In some cases, the parameter may appear more than once or in more than one data list in order to group certain related parameters together.

4WD Low Signal: This parameter displays the state of the transfer case based on the signal from the four wheel drive (4WD) low switch. The scan tool will display Enabled or Disabled. Enabled indicates the transfer case is in 4WD low gear and the 4WD low switch is closed, completing the low signal circuit. Disabled indicates the transfer case is not in 4WD low gear and the 4WD low switch is open.

4WD Signal: This parameter displays the state of the transfer case based on the signal from the front axle indicator switch. The scan tool will display Enabled or Disabled. Enabled indicates the front axle is locked in 4WD and the front axle indicator switch is closed, supplying voltage to the controller on the axle switch signal circuit. Disabled indicates the transfer case is not in 4WD and the front axle indicator switch is open.

5-Volt Reference 1: This parameter displays the diagnostic state of the output driver for the 5-Volt reference 1 circuits. The scan tool will display OK if the circuit is operating correctly. The scan tool will display Fault if there is a short to ground or short to voltage on the circuit.

5-Volt Reference 2 This parameter displays the diagnostic state of the output driver for the 5-Volt reference 2 circuits. The scan tool will display OK if the circuit is operating correctly. The scan tool will display Fault if there is a short to ground or short to voltage on the circuit.

5-Volt Reference 3: This parameter displays the diagnostic state of the output driver for the 5-Volt reference 3 circuits. The scan tool will display OK if the circuit is operating correctly. The scan tool will display Fault if there is a short to ground or short to voltage on the circuit.

A/C Clutch Feedback Signal: This parameter displays the state of the air conditioning (A/C) compressor clutch based on the signal from the switched side of the A/C clutch relay. The scan tool will display Relay On or Relay Off. Relay On indicates the A/C clutch relay has closed, allowing voltage to the A/C compressor clutch. Relay Off indicates the A/C clutch relay is open and the A/C compressor clutch is not engaged.

A/C High Side Pressure Sensor: This parameter displays the voltage signal sent to the control module from the A/C high side pressure sensor. The A/C high side pressure sensor has a range of values indicating a low refrigerant pressure when the voltage is low to a high refrigerant pressure when the voltage is high.

A/C Relay Command: This parameter displays the commanded state of the A/C clutch relay control circuit. The scan tool will display ON or OFF. ON indicates the A/C clutch relay control circuit is being grounded by the control module, allowing voltage to the A/C compressor clutch. OFF indicates the A/C clutch relay is not being commanded on by the control module.

A/C Request Signal: This parameter displays the state of the A/C request input to the control module from the heating, ventilation, and air conditioning (HVAC) controls. The scan tool will display Yes or No. Yes indicates the control module is receiving a request from the HVAC system to ground the A/C clutch relay control circuit, engaging the A/C compressor clutch. No indicates the control module is not receiving a request from the HVAC system to ground the A/C clutch relay control circuit.

A/C Sec. High Pressure Switch: This parameter displays the state of the A/C secondary high pressure switch as determined by the control module. The scan tool will display Open or Closed. Open indicates the A/C refrigerant pressure is not too high to operate the air conditioning. Closed indicates the refrigerant pressure is abnormally high and has closed the A/C secondary high pressure switch.

Actual Fuel Rail Pressure: This parameter displays the fuel rail pressure as calculated by the control module using the signal from the fuel rail pressure (FRP) sensor. The actual fuel rail pressure is a range of values indicating a low pressure when the fuel rail pressure is low to a high pressure when the fuel rail pressure is high. This value is listed in MPa or psi.

APP Indicated Angle: This parameter displays the angle of the accelerator pedal as calculated by the control module using the signals from the accelerator pedal position sensors. The accelerator pedal position (APP) indicated angle is a range of values indicating a low percentage when the accelerator pedal is not depressed to a high percentage when the accelerator pedal is fully depressed.

APP Sensor 1: This parameter displays the voltage signal sent to the control module from APP sensor 1 of the APP sensor assembly. APP sensor 1 is a range of values indicating a low voltage when the accelerator pedal is not depressed to a high voltage when the accelerator pedal is fully depressed.

APP Sensor 2: This parameter displays the voltage signal sent to the control module from APP sensor 2 of the APP sensor assembly. APP sensor 2 is a range of values indicating a low voltage when the accelerator pedal is not depressed to a high voltage when the accelerator pedal is fully depressed.

Balancing Rate Cyl. 1-8: These parameter display the adjustment in fuel volume for each cylinder as calculated by the control module. The scan tool will display a negative balancing rate if the fuel volume is lowered. The scan tool will display a positive balancing rate if the fuel volume is increased.

BARO: This parameter displays the barometric pressure as calculated by the control module using the signal from the barometric pressure (BARO) sensor. The scan tool will display a high value at higher barometric pressures, such as sea level. The scan tool will display a lower value at lower barometric pressures, such as higher altitude locations.

Calculated Fuel Rate: This parameter displays the fuel rate of the fuel injection pump as calculated by the control module.

CAM Signal Present: This parameter displays the state of the CAM signal as determined by the control module. The scan tool will display Yes if the CAM signal is being received by the control module. The scan tool will display No if the CAM signal is missing.

Check Trans Lamp: This parameter displays the commanded state of the check trans lamp control circuit. The check trans lamp should be on when the scan tool indicates the check trans lamp is commanded ON. The check trans lamp should be off when the scan tool indicates the check trans lamp is commanded OFF. The control module will command the check trans lamp On when the ignition is ON with the engine OFF in order to perform a bulb check.

CKP Sensor Signal Present: This parameter displays an incrementing counter when the control module receives a signal from the crankshaft position (CKP) sensor. The scan tool will display an incrementing counter when the CKP signal is being received by the control module. The scan tool will display a steady number when the CKP signal is not being received by the control module.

Clutch Pedal Switch: This parameter displays the current state of the clutch pedal as determined by the control module. The scan tool will display Applied when the clutch pedal is depressed, and released when the clutch pedal is not depressed.

Coolant Level Switch: This parameter displays the level of engine coolant as determined by the control module. The control module determines the level of the coolant using the signal from a switch used to monitor the engine coolant level. The scan tool will display low when the engine coolant level is low. The scan tool will display OK when the coolant level is correct.

Cruise Control Active: This parameter displays the status of the cruise control system as determined by the control module. The scan tool will display Yes when the cruise control system is in control of vehicle speed. The scan tool will display No when the cruise control system is not operating.

Cruise On/Off Switch: This parameter displays the state of the on/off switch input to the control module. The scan tool will display On when the cruise ON/OFF switch is ON. The scan tool will display OFF when the cruise ON/OFF switch is OFF.

Cruise Resume/Accel Switch: This parameter displays the state of the Resume/Accel switch input to the control module When the cruise control switch is in the ON position and the Resume/Accel switch is activated, the scan tool displays On. When the Resume/Accel switch is released the scan tool displays Off.

Cruise Set/Coast Switch: This parameter displays the state of the Set/Coast switch input to the control module from the cruise control system. When the cruise control switch is in the ON position and the Set/Coast switch is activated, the scan tool displays On. When the Set/Coast switch is released the scan tool displays Off.

Desired EGR Position: This parameter displays the position of the exhaust gas recirculation (EGR) valve commanded by the control module. The scan tool will display 0 percent when the control module is commanding the EGR valve closed. The scan tool will display a higher percentage when the EGR valve is commanded open.

Desired FRP Regulator: This parameter displays the desired current draw of the FRP regulator as calculated by the control module. The scan tool will display a low value if the regulator is commanded open, and a higher value when the regulator is commanded closed.

Desired Fuel Rail Pressure: This parameter displays the desired fuel rail pressure as calculated by the control module. This value is calculated based on engine speed, engine load, and sensor inputs. The scan tool will display a higher value at higher engine speeds and loads, and a lower value at idle.

Desired Idle Speed: This parameter displays the engine idle speed in RPM as commanded by the control module. The control module compensates for various engine loads in order to maintain the desired engine speed at idle. This parameter is not valid unless the engine is running.

Desired TC Vane Position: This parameter displays the position of the turbocharger vane position sensor as the turbocharger vane position is commanded by the control module. The scan tool will display 0 percent when the control module is commanding the vanes open. The scan tool will display a higher percentage when the vanes are commanded closed.

Des. TC Vane Pos. Ctrl. Solenoid: This parameter displays the desired current draw of the turbocharger vane position control solenoid valve as calculated by the control module. The scan tool will display a high value if the solenoid is commanded open, and a lower value when the solenoid is commanded closed.

DTC Set This Ignition: This parameter displays if a diagnostic trouble code (DTC) set during the current ignition cycle.

ECM Reset: This parameter displays the status of the control module this ignition cycle. The scan tool will display Yes when an internal control module reset has occurred this ignition cycle. The scan tool will display NO when no internal control module reset has occurred this ignition cycle.

ECT Sensor: This parameter displays the temperature of the engine coolant calculated by the control module, based on the input from the engine coolant temperature sensor. When the coolant temperature is low, the scan tool will display a low temperature. When the coolant temperature is high, the scan tool will display a high temperature.

EGR Position Sensor: This parameter displays the voltage signal received from the EGR valve position sensor by the control module. The scan tool will display a lower value when the EGR valve is closed, and a higher value when the EGR valve is open.

EGR Position Sensor: This parameter displays EGR valve position as calculated by the control module based on an input from the EGR valve position sensor. The scan tool will display a lower value when the EGR valve is closed, and a higher value when the EGR valve is open.

EGR Position Variance: This parameter displays the difference between the desired EGR valve position calculated by the control module and the actual EGR position input from the EGR valve position sensor. The scan tool will display a higher value if the difference is large, and a lower value if the difference is small.

EGR Solenoid Command: This parameter displays the duty cycle commanded by the control module for the EGR valve. The scan tool will display a high percentage when the EGR valve is commanded open. The scan tool will display a low percentage when the EGR valve is commanded closed.

Engine Oil Level Switch: This parameter displays the status of the engine oil level switch as determined by the control module. The control module uses this information to turn on the low engine oil lamp if the engine oil level remains approximately 1 quart low for a sufficient amount of time. The scan tool will display Low when the engine oil level is low. The scan tool will display OK when the engine oil level is correct.

Engine Oil Life Remaining: This parameter displays the amount engine oil life remaining before requiring an oil change based on calculations by the control module. The scan tool will display lower values as the engine oil life approaches 0 miles.

Engine Oil Pressure Sensor: This parameter displays the pressure of the engine oil as calculated by the control module using a signal from the engine oil pressure (EOP) sensor. The scan tool will display oil pressure when the engine is running. The engine oil pressure sensor has a range of values indicating a low value when the oil pressure is low to a high value when the oil pressure is high.

Engine Run Time: This parameter displays the time elapsed since the engine was started. The scan tool will display the time in hours, minutes and seconds. The engine run time will reset to zero when the engine stops running.

Engine Speed: This parameter displays the speed of the crankshaft as determined by the control module using an input from the CKP sensor. The scan tool will display a high value at high engine speeds and a low value at low engine speeds.

Front Axle Switch: This parameter displays state of the switch used to determine when the front axle is engaged for operation in four wheel drive. The scan tool will display Locked when the front axle is engaged. The scan tool will display Unlocked when the front axle is disengaged.

FRP Regulator Command: This parameter displays the fuel rail pressure regulator duty cycle as commanded by the control module. The scan tool will display a lower value for a higher commanded fuel pressure, and a higher value for a lower commanded fuel pressure.

FRP Regulator Command: This parameter displays the current draw of the fuel pressure regulator through the control module. The scan tool will display a higher value for a higher commanded current, and a lower value for a lower commanded current.

Fuel Level Sensor: This parameter displays the voltage received by the control module from the sensor used to monitor the fuel level inside the fuel tank. The scan tool will display a low voltage when the fuel level in the tank is low or near empty. The scan tool will display a high voltage reading when the fuel level in the tank is high or near full.

Fuel Level Sensor: This parameter displays the approximate fuel level in the fuel tank as calculated by the control module based on inputs from the fuel level sensors. The scan tool will display a low value when the fuel level in the tank is low or near empty. The scan tool will display a high value when the fuel level in the tank is high or near full.

Fuel Level Sensor Rear: This parameter displays the voltage received by the control module from the sensor used to monitor the fuel level inside the rear fuel tank. The scan tool will display a low voltage when the fuel level in the tank is low or near empty. The scan tool will display a high voltage reading when the fuel level in the tank is high or near full.

Fuel Temperature Sensor: This parameter displays the current fuel temperature as calculated by the control module based on input from the fuel temperature sensor. The scan tool will display a higher value at higher fuel temperatures. The scan tool will display a lower value at lower fuel temperatures.

GEN L-Terminal Signal: This parameter indicates whether the control module is allowing the generator to operate. The control module can disable the generator under certain conditions. The scan tool will display voltage if the control module is allowing generator operation, while no voltage indicates that the control module is not allowing generator operation.