62. Engine Block Plug Installation

Engine Block Plug Installation

^ Tools Required
- J 41712 Oil Pressure Switch Socket





1. Apply sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent to the threads of the engine coolant drain hole plug.

Notice: Refer to Fastener Notice in Service Precautions.

2. Install the engine coolant drain hole plug into the block.
^ Tighten the engine coolant drain hole plug to 60 Nm (40 ft. lbs.).





3. Apply sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent to the threads of the engine block coolant heater, if applicable.
4. Install the engine block coolant heater into the block.
^ Tighten the engine block coolant heater to 50 Nm (37 ft. lbs.).





5. Apply sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent to the threads of the oil gallery plugs.
6. Install the engine block top oil gallery plugs.
^ Tighten the top oil gallery plugs to 20 Nm (15 ft. lbs.).





7. Apply sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent to the threads of the left side oil gallery plug.
8. Install the engine block left side oil gallery plug.
^ Tighten the left side oil gallery plug to 30 Nm (22 ft. lbs.).





9. Apply sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent to the threads of the front oil gallery plugs.
10. Install the front oil gallery plugs.
^ Tighten the front oil gallery plugs to 30 Nm (22 ft. lbs.).





11. Apply sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent to the threads of the rear oil gallery plugs.
12. Install the rear oil gallery plugs.
^ Tighten the rear oil gallery plugs to 20 Nm (15 ft. lbs.).





13. Apply sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent to the threads of the engine block oil cooler hose fittings.
14. Install the engine block oil cooler hose fittings.
^ Tighten the engine block oil cooler hose fittings to 23 Nm (17 ft. lbs.).





Important: Do not overtighten the knock sensor.

15. Install the left knock sensor to the engine block.
^ Tighten the left knock sensor to 20 Nm (15 ft. lbs.).





16. Install the left side knock sensor heat shield.
17. Install the left side knock sensor heat shield bolts.
^ Tighten the bolts to 12 Nm (106 inch lbs.).





Important: Do not overtighten the knock sensor.

18. Install the right knock sensor (719) to the engine block.
^ Tighten the right side knock sensor to 20 Nm (15 ft. lbs.).
19. Install the right side knock sensor heat shield (720) and bolts (721).
^ Tighten the bolts to 12 Nm (106 inch lbs.).





20. Apply sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent to the threads of the engine block coolant drain hole plugs.
21. Install the engine block coolant drain hole plugs.
^ Tighten the coolant drain hole plugs to 30 Nm (22 ft. lbs.).





22. Apply sealer GM P/N 12377901 (Canadian P/N 10953504), to the outside diameter of the new camshaft rear bearing hole plug.





23. Install the NEW camshaft rear bearing hole plug to the proper depth of (a) 6.2 - 7.6 mm (0.244 - 0.299 inch).





24. Apply sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent to the threads of the oil pressure sensor.
25. Install the oil pressure sensor.
Using the J 41712 (1), tighten the oil pressure sensor to 30 Nm (22 ft. lbs.).