P0615
DTC P0615
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview) provides an overview of each diagnostic category.
DTC Descriptor
DTC P0615
- Starter Relay Control Circuit
Diagnostic Fault Information
Circuit/System Description
When the ignition switch is placed in the start position, a discrete signal is supplied to the body control module (BCM) notifying it that the ignition is in the start position. The BCM then sends a message to the engine control module (ECM) that crank has been requested. The ECM then verifies that the clutch is pressed for the manual transmission or that the automatic transmission is in park or neutral. If it is, the ECM then supplies 12 volts to the control circuit of the STRTR relay. When this occurs, battery voltage is supplied through the switch of the STRTR relay to terminal A X1 of the starter solenoid.
Conditions for Running the DTC
* The ignition is ON.
* The system voltage is between 9.5-18 volts.
Conditions for Setting the DTC
The ECM detects improper voltage on the control circuit of the starter relay for 2 seconds.
Action Taken When the DTC Sets
DTC P0615 is a type C DTC.
Conditions for Clearing the DTC
DTC P0615 is a type C DTC.
Reference Information
Schematic Reference
Starting and Charging Schematics ([1][2]Electrical Diagrams)
Connector End View Reference
Component Connector End Views (Connector Views)
Description and Operation
Starting System Description and Operation (Description and Operation)
Electrical Information Reference
* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Verification
1. Ignition ON. Verify that no theft deterrent, or automatic transmission DTCs are set that would cause the ECM to disable engine starting.
• If any DTCs are set that would cause the ECM to disable starting, then refer to Diagnostic Trouble Code (DTC) List - Vehicle (Diagnostic Trouble Code Descriptions) .
2. Clear the DTCs. Attempt to start the engine. The engine should crank and DTC P0615 should not set.
Circuit/System Testing
1. Ignition OFF, disconnect the STRTR relay.
2. Ignition OFF and scan tool disconnected, open and close the driver door, and wait 1 minute. Test for less than 5 ohms between the relay ground circuit terminal 85 and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
3. Connect a test lamp between the control circuit terminal 86 and the ground circuit terminal 85. Turn the ignition to the start position. The test lamp should turn ON for no longer than 10 seconds when the ignition is in the start position, and OFF in all other positions.
• If the test lamp is always on, test the control circuit for short to voltage. If the circuit tests normal, replace the ECM.
• If the test lamp is always off, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.
4. If all circuits test normal, test or replace the STRTR relay.
Component Testing
STRTR Relay
1. Ignition OFF, disconnect the STRTR relay.
2. Test for 60-180 ohms between terminals 85 and 86 of the relay.
• If not within the specified range, replace the STRTR relay.
3. Test for infinite resistance between the following terminals:
* 30 and 86
* 30 and 87
* 30 and 85
* 85 and 87
• If not the specified value, replace the relay.
4. Install a 20 amp fused jumper wire between relay terminal 85 and 12 volts. Install a jumper wire between relay terminal 86 and ground. Test for less than 2 ohms between terminals 30 and 87 of the relay.
• If greater than specified range, replace the relay.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Relay Replacement (Attached to Wire Harness) (Relay Replacement (Attached to Wire Harness))Relay Replacement (Within an Electrical Center) (Relay Replacement (Within an Electrical Center))
* Control Module References (Programming and Relearning) for ECM replacement, setup, and programming.