Recall - ECM/TCM Update For A/T 1st Gear Downshift: Overview
# 08218A: Product Safety - Transmission Damage Due to Engine Shutdown and/or First Gear Engagement at Highway Speeds - (Aug 15, 2008)Subject:
08218 -- Transmission Damage Due to Engine Shutdown And / Or First Gear Engagement at Highway Speeds
Models:
2008 Chevrolet Express G-Cutaway and Cargo Vans
2008 GMC Savana G-Cutaway and Cargo Vans
Equipped with 4.8L or 6.0L (RPO LY2, LY6 - VIN C, K) V8 Engine and 4L80E (RPO MT1) Transmission and 3.73/4.10 (RPO GT4, GT5) Axle and 65 or 75 MPH (105 or 121 KPH) Governor (RPO 9D7)
THIS BULLETIN IS BEING REVISED TO ADD VEHICLES TO THE RECALL. PLEASE DISCARD ALL COPIES OF BULLETIN 08218, ISSUED JULY 2008.
Condition
General Motors has decided that a defect, which relates to motor vehicle safety, exists in certain 2008 model year Chevrolet Express and GMC Savana G-Cutaway one way rental fleet and Cargo van model vehicles, equipped with a 4.8L or 6.0L (RPO LY2, LY6 - VIN C, K) V8 engine and 4L80E (RPO MT1) automatic transmission and 3.73/4.10 (RPO GT4, GT5) axle and 65 or 75 MPH (105 or 121 KPH) governor. These vehicles have a condition in which the transmission may be damaged due to first gear engagement at highway speeds and then does not transmit power with D4 or R selected. This may be preceded by engine shutdown if the vehicle exceeds the speed governor miles (kms) per hour in certain driving conditions. The vehicle may be stranded on or near a highway, increasing the risk of a crash.
If the engine has shutdown, it can be restarted. In some cases, the transmission will not function in any gear. In most cases, if the driver shifts to a lower gear, the vehicle will have a limited operating capability, depending on loads and the extent of transmission damage.
Correction
Dealers are to reprogram the Transmission Control Module (TCM) and Engine Control Module (ECM).
Vehicles Involved
Involved are certain 2008 model year Chevrolet Express and GMC Savana G-Cutaway one way rental fleet and Cargo van model vehicles, equipped with a 4.8L or 6.0L (RPO LY2, LY6 - VIN C, K) V8 engine and 4L80E (RPO MT1) automatic transmission and 3.73/4.10 (RPO GT4, GT5) axle and 65 or 75 MPH (105 or 121 KPH) governor, and built within the VIN breakpoints shown above.
Important:
Dealers are to confirm vehicle eligibility prior to beginning repairs by using the system(s) below. Not all vehicles within the above breakpoints may be involved.
-- GM dealers should use GMVIS.
For dealers with involved vehicles, a listing with involved vehicles containing the complete vehicle identification number, customer name, and address information has been prepared and will be provided through the applicable system listed below. Dealers will not have a report available if they have no involved vehicles currently assigned.
-- US GM dealers - GM DealerWorld Recall Information
-- Canadian GM dealers - GMinfoNet Recall Reports
The listing may contain customer names and addresses obtained from Motor Vehicle Registration Records. The use of such motor vehicle registration data for any purpose other than follow-up necessary to complete this recall is a violation of law in several states/provinces/countries. Accordingly, you are urged to limit the use of this report to the follow-up necessary to complete this recall.
Calibration Information
Do not attempt to order the calibration number from GMSPO. The calibration numbers required for this service procedure are programmed into control modules via a Multiple Diagnostic Interface (MDI) or Tech 2(R) scan tool and TIS2WEB with the calibration update. Use TIS2WEB data version 8.0 for 2008 on or after 07/30/08 to obtain the calibration. If you cannot access the calibration, call the Techline Customer Support Center and it will be provided.
Service Procedure
Important:
Verify that the 12-volt battery has a battery charge of 12 to 16 volts. The battery must be able to maintain a charge during programming. Only use approved Midtronics 165-PCS charger or equivalent to maintain proper battery voltage during programming. The J2534 MDI will reprogram the modules in less time than the Tech 2(R) scan tool.
Updated ECM and TCM calibrations are now available to address these concerns. Reprogram the controllers with the updated calibration files using the TIS2WEB Service Programming System (SPS) application.
1. Verify that there is a battery charge of 12 to 16 volts. The battery must be able to maintain a charge during programming. Only use approved Midtronics 165 PCS charger, a fully charged 12V jumper, or booster pack disconnected from the AC voltage supply to maintain proper battery voltage during programming.
2. Reprogram both the engine control module (ECM) and transmission control module (TCM). Refer to SI and Service Programming System (SPS) documentation for programming instructions, if required.
3. Select J2534 MDI or Tech 2(R) Legacy Pass-Thru and Reprogram ECU from the Select Diagnostic Tool and Programming Process screen.
4. Select ECM Engine Control Module from the Supported Controllers screen.
5. Follow the on-screen instructions for programming the ECM.
6. Using the MDI or Tech 2(R), clear all DTCs if required.
7. Select TCM Transmission Control Module from the Supported Controllers screen.
8. Follow the on-screen instructions for programming TCM.
9. Using the MDI or Tech2(R), clear all DTCs if required.
Courtesy Transportation -- For US and Canada
The General Motors Courtesy Transportation program is intended to minimize customer inconvenience when a vehicle requires a repair that is covered by the New Vehicle Limited Warranties. The availability of courtesy transportation to customers whose vehicles are within the warranty coverage period and involved in a product program is very important in maintaining customer satisfaction. Dealers are to ensure that these customers understand that shuttle service or some other form of courtesy transportation is available and will be provided at no charge. GM dealers should refer to the General Motors Service Policies and Procedures Manual for Courtesy Transportation guidelines.
Claim Information
Submit a Product Recall Claim with the information shown.
Customer Notification -- For US and Canada
General Motors will notify customers of this recall on their vehicle (see copy of customer letter shown in this bulletin).
Dealer Recall Responsibility - For US (US States, Territories, and Possessions)
The US National Traffic and Motor Vehicle Safety Act provides that each vehicle that is subject to a recall of this type must be adequately repaired within a reasonable time after the customer has tendered it for repair. A failure to repair within sixty days after tender of a vehicle is prima facie evidence of failure to repair within a reasonable time. If the condition is not adequately repaired within a reasonable time, the customer may be entitled to an identical or reasonably equivalent vehicle at no charge or to a refund of the purchase price less a reasonable allowance for depreciation. To avoid having to provide these burdensome remedies, every effort must be made to promptly schedule an appointment with each customer and to repair their vehicle as soon as possible. In the recall notification letters, customers are told how to contact the US National Highway Traffic Safety Administration if the recall is not completed within a reasonable time.
Dealer Recall Responsibility - All
All unsold new vehicles in dealers' possession and subject to this recall must be held and inspected/repaired per the service procedure of this recall bulletin before customers take possession of these vehicles.
Dealers are to service all vehicles subject to this recall at no charge to customers, regardless of mileage, age of vehicle, or ownership, from this time forward.
Customers who have recently purchased vehicles sold from your vehicle inventory, and for which there is no customer information indicated on the dealer listing, are to be contacted by the dealer. Arrangements are to be made to make the required correction according to the instructions contained in this bulletin. A copy of the customer letter is shown in this bulletin for your use in contacting customers. Recall follow-up cards should not be used for this purpose, since the customer may not as yet have received the notification letter.
In summary, whenever a vehicle subject to this recall enters your vehicle inventory, or is in your dealership for service in the future, you must take the steps necessary to be sure the recall correction has been made before selling or releasing the vehicle.
Disclaimer