Operation CHARM: Car repair manuals for everyone.
Home >> GMC Truck >> 2009 >> Acadia FWD V6-3.6L >> Repair and Diagnosis >> Steering and Suspension >> Steering >> Steering Column >> Service and Repair >> Steering Column Replacement

Steering Column Replacement




Steering Column Replacement

Removal Procedure

Caution: Secure the steering wheel utilizing a strap to prevent rotation. Locking of the steering column will prevent damage and a possible malfunction of the SIR system. The steering wheel must be secured in position before disconnecting the following components:

* The steering column
* The intermediate shaft
* The steering gear

After disconnecting these components, do not move the front tires and wheels. Failure to follow these procedures may cause improper alignment of some components during installation and result in possible damage to the SIR coil.

1. Remove the left side instrument panel (I/P) insulator panel. Refer to Instrument Panel Insulator Panel Replacement - Left Side (Acadia) (Service and Repair)Instrument Panel Insulator Panel Replacement - Left Side (Enclave) (Service and Repair)Instrument Panel Insulator Panel Replacement - Left Side (OUTLOOK) (Service and Repair)Instrument Panel Insulator Panel Replacement - Left Side (Traverse) (Service and Repair).
2. Remove the driver knee bolster. Refer to Driver Knee Bolster Replacement (Traverse) (Service and Repair)Driver Knee Bolster Replacement (Acadia) (Service and Repair)Driver Knee Bolster Replacement (Enclave) (Service and Repair)Driver Knee Bolster Replacement (OUTLOOK) (Service and Repair).
3. Remove the I/P cluster trim plate applique for Buick. Refer to Instrument Panel Cluster Trim Plate Applique Replacement (Enclave) (Service and Repair).
4. Remove the I/P Instrument Cluster Trim Plate for GMC, Saturn, and Chevrolet. Refer to Instrument Panel Cluster Trim Plate Replacement (OUTLOOK) (Instrument Panel Cluster Trim Plate Replacement)Instrument Panel Cluster Trim Plate Replacement (Acadia) (Instrument Panel Cluster Trim Plate Replacement)Instrument Panel Cluster Trim Plate Replacement (Traverse) (Instrument Panel Cluster Trim Plate Replacement).
5. Remove the steering column housing cover bolts. Refer to Steering Column Housing Cover Replacement (Traverse) ()Steering Column Housing Cover Replacement (Acadia) (Service and Repair)Steering Column Housing Cover Replacement (Enclave) (Service and Repair)Steering Column Housing Cover Replacement (OUTLOOK) ().
6. Disconnect all electrical connectors as needed.




7. If equipped, remove the steering column lower support brace bolts (1) and steering column lower support brace (2).




8. Remove the intermediate steering shaft bolt (1) at the steering column and separate the intermediate steering shaft (2). Do not pull the intermediate steering shaft upper seal (3) from its place.




9. Remove the steering column nuts (2) and the steering column bolts (1).
10. Remove the steering column from the vehicle.
11. Transfer any parts as needed.

Installation Procedure





Note: The following sequence MUST be followed. Make sure to hand tighten ONLY in the sequence specified and DO NOT apply any clamping force.

1. Install the steering column to the vehicle and start the steering column nuts (3, 4) and bolts (1, 2) by hand using the following sequence:

1. Place the steering column in place.
2. Hand start the steering column nuts (3, 4).
3. Hand start the steering column bolts (1, 2).
4. Hold the steering column flush against the I/P carrier.
5. Hand tighten steering column nut (3).
6. Hand tighten steering column nut (4).
7. Hand tighten steering column bolt (1).
8. Hand tighten steering column bolt (2).

Caution: Refer to Fastener Caution (Fastener Caution).

Note: The following torque sequence MUST be followed.

2. Tighten the steering column nuts (3, 4) and bolts (1, 2) in the following sequence:

1. Tighten steering column nut (3) to 27 Nm (20 lb ft).
2. Tighten steering column nut (4) to 27 Nm (20 lb ft).
3. Tighten steering column bolt (1) to 27 Nm (20 lb ft).
4. Tighten steering column bolt (2) to 27 Nm (20 lb ft).




3. Install the intermediate steering shaft (2) and intermediate steering shaft bolt (1). Make sure the intermediate steering shaft upper seal (3) is seated correctly.




4. If equipped, install the steering column lower support brace (2) and steering column lower support brace bolts (1) and tighten to 10 Nm (89 lb in).
5. Connect all electrical connectors as needed.
6. Install the steering column housing cover bolts. Refer to Steering Column Housing Cover Replacement (Traverse) ()Steering Column Housing Cover Replacement (Acadia) (Service and Repair)Steering Column Housing Cover Replacement (Enclave) (Service and Repair)Steering Column Housing Cover Replacement (OUTLOOK) ().
7. Install the I/P Instrument Cluster Trim Plate for GMC. Saturn, and Chevrolet. Refer to Instrument Panel Cluster Trim Plate Replacement (OUTLOOK) (Instrument Panel Cluster Trim Plate Replacement)Instrument Panel Cluster Trim Plate Replacement (Acadia) (Instrument Panel Cluster Trim Plate Replacement)Instrument Panel Cluster Trim Plate Replacement (Traverse) (Instrument Panel Cluster Trim Plate Replacement).
8. Install the I/P cluster trim plate applique for Buick. Refer to Instrument Panel Cluster Trim Plate Applique Replacement (Enclave) (Service and Repair).
9. Install the left side I/P insulator panel. Refer to Instrument Panel Insulator Panel Replacement - Left Side (Acadia) (Service and Repair)Instrument Panel Insulator Panel Replacement - Left Side (Enclave) (Service and Repair)Instrument Panel Insulator Panel Replacement - Left Side (OUTLOOK) (Service and Repair)Instrument Panel Insulator Panel Replacement - Left Side (Traverse) (Service and Repair).

pro multis · About Operation CHARM