Dual DVD Rear Seat Entertainment Headrest Display Malfunction

Dual DVD Rear Seat Entertainment Headrest Display Malfunction

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (with HP2) (Initial Inspection and Diagnostic Overview)Diagnostic System Check - Vehicle (without HP2) (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview) provides an overview of each diagnostic category.

Diagnostic Fault Information





Circuit Description

The DVD displays are grounded and powered by the DVD control module. When a movie is playing, the video signals are sent from the player, to the DVD control module, and back to the display. This allows the other monitor to source the same video as the player with the disc.

Reference Information
Schematic Reference

Video System Schematics (Video System Schematics)
Connector End View Reference

Component Connector End Views (Connector Views)
Description and Operation

Video Entertainment System Description and Operation (Non-Headrest DVD Systems) (Video Entertainment System Description and Operation (Non-Headrest DVD Systems))Video Entertainment System Description and Operation (Dual Headrest DVD Systems) (Video Entertainment System Description and Operation (Dual Headrest DVD Systems))
Electrical Information Reference

* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)

Scan Tool Reference

Control Module References (Programming and Relearning) for scan tool information

Circuit/System Testing

One Display Inoperative
1. Ignition OFF, disconnect the X1 harness connector at the appropriate display.
2. Ignition ON, test for less than 5 Ohms between the ground circuit terminal 5 and ground.

• If greater than the specified range, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the DVD control module.

3. Ignition ON, test for B+ between the ignition voltage circuit terminal 6 and ground.

• If less than the specified value, B+ circuit for an open/high resistance. If the circuit tests normal, replace the DVD control module.

4. Ignition OFF, reconnect the X1 harness connector, and disconnect the X2 harness connector at the display.
5. Ignition ON, test for 4.5-5.5 V between the terminals listed below and ground:

* I2C Clock Signal -terminal 5
* I2C Data -terminal 6

• If less than specified range, test the signal circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the DVD control module.
• If greater than specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the DVD control module.

6. If all circuits test normal, replace the appropriate display.

Both Displays Inoperative
1. Ignition OFF, disconnect the X1 harness connector at the DVD control module.
2. Test for less 5 Ohms between the ground circuit terminal 3 and ground.

• If the greater than the specified range, test the ground circuit for an open/high resistance.

3. Ignition ON, test for B+ between the accessory voltage circuit terminal and ground.

• If less than the specified value, test the B+ circuit for a short to ground or an open/high resistance.

4. Ignition OFF, Reconnect the X1 harness connector at the DVD control module
5. Disconnect the X1 harness connector at the driver seat headrest.
6. Ignition ON, test for less than 5 Ohms between the ground circuit terminal 5 and ground.

• If greater than the specified range, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the DVD control module.

7. Ignition ON, test for B+ between the ignition voltage circuit terminal 6 and ground.

• If less than the specified value, B+ circuit for an open/high resistance. If the circuit tests normal, replace the DVD control module.

8. Ignition OFF, reconnect the X1 harness connector, and disconnect the X2 harness connector at the display.
9. Ignition ON, test for 4.5-5.5 V between the terminals listed below and ground:

* I2C Clock Signal -terminal 5
* I2C Data -terminal 6

• If less than specified range, test the signal circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the DVD control module.
• If greater than specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the DVD control module.

10. If all circuits test normal, replace the appropriate display.