Headlamps Malfunction
Headlamps Malfunction
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.
Diagnostic Fault Information
Circuit/System Description
With the headlamp switch in the ON position, the headlamp switch headlamp ON signal circuit is grounded through the headlamp switch. In response to this input, the body control module (BCM) provides ground to either the headlamp low beam relay control circuit or the headlamp high beam relay control circuit. The position of the headlamp dimmer switch determines which relay coil is supplied with ground. The BCM supplies ground to the relay coil circuits, if the headlamps are necessary. The underhood fuse block supplies battery voltage to the relay coil and switch circuits. The low beam headlamps operate when the BCM grounds the relay coil control circuit to the relay coil of the low beam headlamp relay. This energizes the low beam relay causing the switch contacts to close. With the switch contacts closed, battery voltage is applied to the LT-LO HDLP and RT-LO HDLP beam fuses through to the left and right low beam headlamps. When the headlamp high beam relay coil is energized, current flows through the LT-HI HEADLAMP and the RT-HI HEADLAMP fuses to the high beam headlamps. With the headlamp dimmer switch in the high beam position the BCM sends a serial data message to the instrument panel cluster (IPC) requesting the IPC to illuminate the high beam indicator.
Reference Information
Schematic Reference
Headlights/Daytime Running Lights (DRL) Schematics (Headlights/Daytime Running Lights (DRL) Schematics)
Connector End View Reference
Component Connector End Views (Connector Views)
Description and Operation
Exterior Lighting Systems Description and Operation (Exterior Lighting Systems)
Electrical Information Reference
* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Verification
1. Ignition ON, observe the scan tool Headlamp Switch parameter while turning the headlamp switch ON and OFF. The reading should change between Active and Inactive.
• If the reading does not change between the selected states, refer to Headlamp Switch Malfunction.
2. Observe the scan tool Auto Hdlp. Disable Sw. parameter while turning the headlamp switch ON and OFF. The reading should toggle between Active and Inactive.
• If the reading does not change between the selected states, refer to Headlamp Switch Malfunction.
3. Observe the scan tool Flash to Pass Switch parameter while applying and releasing the turn signal/multifunction switch. The reading should toggle between Active and Inactive.
• If the reading does not change between the selected states, refer to Turn Signal/Multifunction Switch Malfunction.
4. Observe the scan tool High Beam Select Switch parameter while applying and releasing the high beam select switch. The reading should toggle between Active and Inactive.
• If the reading does not change between the selected states, refer to Turn Signal/Multifunction Switch Malfunction.
5. Command the Low Beams ON and OFF with a scan tool. The low beam headlamps should turn ON and OFF when commanded.
• If the low beam headlamps do not turn ON and OFF when commanded, refer to Headlamps Malfunction - Low Beam.
6. Command the High Beams ON and OFF with a scan tool. The high beam headlamps should turn ON and OFF when commanded.
• If the high beam headlamps do not turn ON and OFF when commanded, refer to Headlamps Malfunction - High Beam.
7. Command the Lamp Test ON and OFF with a scan tool. The high beam indicator should turn ON and OFF when changing between the commanded states.
• If the high beam indicator illuminates during the test, replace the BCM.
• If the high beam indicator does not illuminate during the test or remain illuminated at all times, replace the instrument cluster.
Circuit/System Testing
Headlamp Switch Malfunction
1. Ignition OFF, disconnect the harness connector at the headlamp and panel dimmer switch.
2. Verify that a test lamp illuminates between B+ and the ground circuit terminal 8.
• If the test lamp does not illuminate, test the ground circuit for an open/high resistance.
3. Ignition ON, verify the scan tool Headlamp Switch parameter is Inactive.
• If not the specified value, test the signal circuit terminal 1 for short to ground. If the circuit tests normal, replace the BCM.
4. Verify the scan tool Auto Hdlp. Disable Sw. parameter is Inactive.
• If not the specified value, test the signal circuit terminal 3 for short to ground. If the circuit tests normal, replace the BCM.
5. Install a 3 A fused jumper wire between the signal circuit terminal 1 and ground. Verify the scan tool Headlamp Switch parameter is Active.
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.
6. Install a 3 A fused jumper wire between the signal circuit terminal 3 and ground. Verify the scan tool Auto Hdlp. Disable Sw. parameter is Active.
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.
7. If all circuits test normal, test or replace the headlamp and panel dimmer switch.
Turn Signal/Multifunction Switch Malfunction
1. Ignition OFF, disconnect the X2 harness connector at the turn signal/multifunction switch.
2. Verify that a test lamp illuminates between B+ and the ground circuit terminal D.
• If the test lamp does not illuminate, test the ground circuit for an open/high resistance.
3. Verify the scan tool High Beam Select switch parameter is Inactive.
• If not the specified value, test the signal circuit terminal E for a short to ground. If the circuit tests normal, replace the BCM.
4. Verify the scan tool Flash to Pass Switch parameter is Inactive.
• If not the specified value, test the signal circuit terminal A for a short to ground. If the circuit tests normal, replace the BCM.
5. Install a 3 A fused jumper wire between the signal circuit terminal E and ground. Verify the scan tool High Beam Select Switch parameter is Active.
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.
6. Install a 3 A fused jumper wire between the signal circuit terminal A and ground. Verify the scan tool Flash to Pass Switch parameter is Active.
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.
7. If all circuits test normal, test or replace the signal/multifunction switch.
Headlamps Malfunction - Low Beam
1. Ignition OFF, disconnect the low beam relay.
2. Ignition ON, verify that a test lamp does not illuminate between the control circuit terminal 87 and ground.
• If the test lamp illuminates, test the control circuit for a short to voltage.
3. Verify that a test lamp illuminates between the B+ circuit terminal 86 and ground.
• If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
4. Verify that a test lamp illuminates between the B+ circuit terminal 30 and ground.
• If the test lamp does not illuminate, test the B+ circuit for an open/high resistance.
5. Disconnect the harness connector at the appropriate headlamp - low beam.
6. Test for less than 5 ohm between the headlamp - low beam ground circuit terminal B and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
7. Connect the harness connector at the headlamp - low beam.
8. Connect a 20 A fused jumper wire between the B+ circuit terminal 30 and the control circuit terminal 87. Verify the headlamp - low beam is activated.
• If the headlamp - low beam does not activate and the circuit fuse is good, test the control circuit for an open/high resistance. If the circuit tests normal, test or replace the headlamp - low beam.
• If the headlamp - low beam does not activate and the circuit fuse is open, test the control circuit for a short to ground. If the circuit tests normal, test or replace the headlamp - low beam.
9. Connect a test lamp between the B+ circuit terminal 86 and the control circuit terminal 85.
10. Command the Low Beams ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
• If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the BCM.
• If the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.
11. If all circuits test normal, test or replace the low beam relay.
Headlamps Malfunction - High Beam
1. Ignition OFF, disconnect the X4 harness connector at the fuse block-underhood.
2. Connect a test lamp between the control circuit terminal C3 and B+.
3. Command the High Beams ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
• If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the BCM.
• If the test lamp is always OFF, test the control circuit for a short to voltage or open/high resistance. If the circuit tests normal, replace the BCM.
4. Ignition OFF, connect the X4 harness connector at the fuse block-underhood. Disconnect the harness connector at the appropriate high beam headlamp.
5. Ignition OFF, scan tool OFF, exterior lamps OFF, test for less than 5.0 ohm between the ground circuit terminal B and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
6. Connect a test lamp between the control circuit terminal A and ground.
7. Command the High Beams ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
• If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the fuse block-underhood.
• If the test lamp is always OFF and the circuit fuse is good, test the control circuit for an open/high resistance. If the circuit tests normal, replace the fuse block-underhood.
• If the test lamp is always OFF and the circuit fuse is open, test the control circuit for a short to ground. If the circuit tests normal, replace the high beam headlamp.
8. If all circuits test normal, replace the high beam headlamp.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Headlamp Switch Replacement (with RPO SLT) (Headlamp Switch Replacement (with RPO SLT))Headlamp Switch Replacement (without RPO SLT) (Headlamp Switch Replacement (without RPO SLT))
* Headlamp Replacement (Chevrolet) (Headlamp Replacement)Headlamp Replacement (GMC ) (Headlamp Replacement)Headlamp Replacement (HD Diesel) (Headlamp Replacement (HD Diesel))
* Headlamp Bulb Replacement (Chevrolet) (Service and Repair)Headlamp Bulb Replacement (GMC) (Service and Repair)
* Relay Replacement (Attached to Wire Harness) (Relay Replacement (Attached to Wire Harness))Relay Replacement (Within an Electrical Center) (Relay Replacement (Within an Electrical Center))
* Underhood Electrical Center or Junction Block Replacement (Underhood Electrical Center or Junction Block Replacement)
* Turn Signal Multifunction Switch Replacement (Turn Signal Multifunction Switch Replacement)
* Control Module References (Programming and Relearning) for BCM or instrument panel replacement, setup, and programming