Cylinder Deactivation (Active Fuel Management) System Diagnosis

Cylinder Deactivation (Active Fuel Management) System Diagnosis

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.

Circuit Description

To provide maximum fuel economy under light load driving conditions, the engine control module (ECM) will command the valve lifter oil manifold (VLOM) solenoids ON, to deactivate engine cylinders 1 and 7 on the left bank, and cylinders 4 and 6 on the right bank. The VLOM consists of 4 electrically operated normally closed solenoids, which directs pressurized engine oil to 8 deactivating valve lifters. All 4 VLOM solenoids are connected in parallel to a fused ignition circuit supplied by the powertrain relay. The control circuit for each solenoid is connected to an individual low side driver internal to the ECM. When enabling conditions for V4 mode are met, the ECM will command each low side driver to turn ON, in engine firing order sequence.

Diagnostic Aids

The VLOM solenoids are assigned to the following engine cylinders:

* Solenoid #1-Cylinder #1
* Solenoid #2-Cylinder #4
* Solenoid #3-Cylinder #6
* Solenoid #4-Cylinder #7

Reference Information
Schematic Reference

Engine Controls Schematics ([1][2]Electrical Diagrams)
Connector End View Reference

Component Connector End Views (Connector Views)
Description and Operation

Cylinder Deactivation (Active Fuel Management) System Description (Cylinder Deactivation (Active Fuel Management) System)
Electrical Information Reference

* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)

Scan Tool Reference

Control Module References (Programming and Relearning) for scan tool information

Circuit/System Verification

1. If sent here from DTC P0300-P0308 (Without Heavy Duty L96) (P0300) , continue with testing. If any other DTCs are set, then repair those DTC first. Refer to Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle).
2. Start and idle the engine.
3. Allow the engine to reach normal engine operating temperature. The engine should idle smoothly without any misfires.
4. Monitor the cylinder deactivation system data parameters with a scan tool.
5. Road test the vehicle under light throttle and load conditions that will allow the ECM to command V4 mode. If all enabling conditions are met for cylinder deactivation, and if no internal engine hydraulic/mechanical fault conditions are present, the ECM will continue operation in V4 mode.

• If the vehicle passes the Circuit/System Verification test, then review the active fuel management driving information in the Features and Controls section of the owners manual with the vehicle operator, or instruct the vehicle operator in the proper driving techniques to obtain V4 mode.
• If the vehicle does not pass the Circuit/System Verification test, then review the cylinder deactivation inhibit reasons listed on the scan tool.

Circuit/System Testing

Electrical System Testing

Ignition ON and the engine OFF, command each VLOM solenoid ON and OFF using the scan tool. Standing next to the engine compartment, you should be able to hear the solenoid energize and de-energize with each command.

If you cannot hear each solenoid energize and de-energize, then refer to DTC P3401, P3425, P3441, or P3449 (P3401).

Mechanical System Testing
1. Connect a vacuum gauge to the EVAP vacuum tube fitting on the electronic throttle body. DO NOT use a compound pressure and vacuum gauge. The vacuum gauge on a hand held vacuum pump will work fine for this test.
2. Start the engine. Allow the engine to reach normal operation temperature.
3. With a scan tool, command each VLOM solenoid ON, one at a time. Each time a solenoid is command ON, you should observe a fluctuating drop of intake manifold vacuum, and a misfire on the cylinder that was deactivated.

• If there is no fluctuating drop in engine vacuum, or the engine does not misfire, then refer to Cylinder Deactivation (Active Fuel Management) System Diagnosis (Component Tests and General Diagnostics).

Repair Instructions

Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.