Radio Does Not Interface with Personal Audio Link Module
Radio Does Not Interface with Personal Audio Link Module
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions)provides an overview of each diagnostic category.
Diagnostic Fault Information
Circuit Description
The Apple iPod(R) is connected to the personal audio link (PAL) through a dedicated interface cable. The cable allows the iPod the ability to share serial data communication, audio signals, power and ground with the vehicle. The T-harness used to connect the PAL module shares the same power and grounds as the radio. The audio signal circuits are shared with the Digital Radio Receiver audio circuits. The PAL module receives Data communication by connecting inline with the DRR.
Diagnostic Aids
* After PAL is installed, it is only possible to communicate with the DRR when the radio is ON and XM band selected.
* If radio is OFF, or tuned to any other band a NO COMM message for DRR is displayed on Tech2 (Vehicle DTC Check).
* PAL module maintains a persistent B1000 code that cannot be cleared, and does not affect operation.
* If PAL module loses power or ground, BCM and Radio set DTCs for loss of communication with DRR.
* The iPod(R) interface connector is susceptible to vibration and movement damage. It is recommended that excessive movement of the iPod(R) and cable be avoided while driving.
Reference Information
Schematic Reference
Radio/Navigation System Schematics (Radio/Navigation System Schematics)
Connector End View Reference
Component Connector End Views (Connector End Views By Name)
Description and Operation
Radio/Audio System Description and Operation (Radio/Audio System)
Electrical Information Reference
* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)
Scan Tool Reference
Control Module References (Control Module References)for scan tool information
Circuit/System Verification
Note: Verify that the iPod(R) is in good working order and visually inspect the iPod(R) connector cavity for any signs of damage before performing this diagnostic. Verify the most up to date software has been downloaded from http://www.apple.com/support/ipod/ to the iPod(R) before performing this diagnostic.
1. Tune to a strong AM or FM station and verify each speaker is producing clear and even sound, with no distortion.
• If any speaker is not producing sound or the sound produced is distorted, refer to Symptoms - Entertainment (Symptoms - Entertainment).
2. Ignition ON, Observe the PAL red LED lamp. Verify the red LED lamp is illuminated.
• If the PAL red LED is not illuminated, go to Circuit/System Testing.
3. Set the radio to the iPod(R) interface menu and attempt to operate audio from the iPod(R).
4. Inspect the interface harness at the connection to the iPod(R) and verify that audio quality from the iPod(R) is not changed when the harness is bent in multiple directions.
• If the audio changes quality or drops out, inspect the iPod(R) connector cavity or interface cable for damage. If no damage found, replace the iPod(R) interface cable.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the PAL module.
2. Test for less than 5 Ohms between terminal 9 and ground.
• If greater than specified value, test the ground circuit for an open/high resistance.
3. Ignition ON, verify that a test lamp illuminates between terminal 16 and ground.
• If the test lamp does not illuminate, test the B+ circuit for an open/high resistance.
4. Ignition OFF, reconnect the harness connector at the PAL module.
5. Ignition ON, set the radio to the iPod(R) interface menu and attempt to operate audio from the iPod(R).
• If the iPod(R) fails to communicate with the radio, replace the interface cable.
6. Near the BCM connector, verify the serial data circuit from PAL is properly spliced to the serial data circuit.
• If the serial data circuit is not connected, reconnect the circuit.
7. Ignition OFF, disconnect the PAL module and the X1 radio harness connector.
8. Test for less than 1 Ohms between terminal 9 at the X1 radio harness connector and terminal 5 at the X1 PAL module harness connector.
• If greater than specified value, replace the T-harness.
9. If all systems test normal, replace the PAL module.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
For PAL replacement, refer to Ipod(R) interface installation instructions.