Front Fog Lamps Malfunction
Front Fog Lamps Malfunction
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
Diagnostic Fault Information
Circuit/System Description
The front fog lamp relay is supplied with battery voltage at all times. The front fog lamp switch signal circuit is grounded momentarily by pressing the front fog lamp switch. The body control module (BCM) energizes the front fog lamp relay by applying ground to the front fog lamp relay control circuit. When the front fog lamp relay is energized, the relay switch contacts close and battery voltage is applied through the front fog lamp fuse to the front fog lamp supply voltage circuit which illuminates the front fog lamps. With the front fog lamp switch activated the BCM sends a message via serial data to the instrument cluster requesting the instrument cluster to illuminate the front fog indicator.
Reference Information
Schematic Reference
Fog Lights Schematics Fog Lights Schematics
Connector End View Reference
Component Connector End Views Sunshade - Left Front
Description and Operation
Exterior Lighting Systems Description and Operation Exterior Lighting Systems
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
Scan Tool Reference
Control Module References Programming and Relearning for scan tool information
Circuit/System Verification
1. Ignition ON, headlamps ON.
2. Verify the scan tool Front Fog Lamps Switch parameter changes between Active and Inactive while commanding the front fog lamps ON and OFF with the front fog lamp switch.
• If the parameter does not change
Refer to Front Fog Lamp Switch Malfunction.
• If the parameter changes
3. Verify the front fog lamps turn ON and OFF when commanding the Front Fog Lamps ON and OFF with a scan tool.
• If the front fog lamps do not turn ON and OFF
Refer to Front Fog Lamps Malfunction.
• If the front fog lamps turn ON and OFF
4. Verify the front fog lamp indicator on the instrument cluster turns ON and OFF while commanding the front fog lamps ON and OFF with the front fog lamp switch.
• If the front fog lamp indicator does not turn ON and OFF
Refer to Front Fog Lamp Indicator Malfunction.
• If the front fog lamp indicator turns ON and OFF
5. All OK.
Circuit/System Testing
Front Fog Lamp Switch Malfunction
1. Ignition OFF, scan tool disconnected, all doors closed, all accessories OFF, disconnect the harness connector at the S78 turn signal/multifunction switch. It may take up to 2 minutes for all vehicle systems to power down.
2. Test for less than 15 ohms between the ground circuit terminal 6 and ground.
• If 15 ohms or greater
1. Ignition OFF.
2. Test for less than 2 ohms in the ground circuit end to end.
• If 2 ohms or greater, repair the open/high resistance in the circuit.
• If less than 2 ohms, repair the open/high resistance in the ground connection.
• If less than 15 ohms
3. Ignition ON.
4. Verify the scan tool Front Fog Lamps Switch parameter is Inactive.
• If not Inactive
1. Ignition OFF, disconnect the X1 harness connector at the K9 body control module.
2. Test for infinite resistance between the signal circuit terminal 1 and ground.
• If less than infinite resistance, repair the short to ground on the circuit.
• If infinite resistance, replace the K9 body control module.
• If Inactive
5. Install a 3 A fused jumper wire between the signal circuit terminal 1 and ground.
6. Verify the scan tool Front Fog Lamps Switch parameter is Active.
• If not Active
1. Ignition OFF, disconnect the X1 harness connector at the K9 body control module, ignition ON.
2. Test for less than 1 V between the signal circuit terminal 1 and ground.
• If 1 V or greater, repair the short to voltage on the circuit.
• If less than 1 V
3. Test for less than 2 ohms in the signal circuit end to end.
• If 2 ohms or greater, repair the open/high resistance in the circuit.
• If less than 2 ohms, replace the K9 body control module.
• If Active
7. Test or replace the S78 turn signal/multifunction switch.
Front Fog Lamps Malfunction
1. Ignition OFF, disconnect the X4 harness connector at the X50A fuse block - underhood.
2. Connect a test lamp between the control circuit terminal K7 and B+, ignition ON.
3. Verify the test lamp turns ON and OFF when commanding the Front Fog Lamps ON and OFF with a scan tool.
• If the test lamp is always OFF
1. Ignition OFF, disconnect the X5 harness connector at the K9 body control module, ignition ON.
2. Test for less than 1 V between the control circuit terminal and ground.
• If 1 V or greater, repair the short to voltage on the circuit.
• If less than 1 V
3. Ignition OFF.
4. Test for less than 2 ohms in the control circuit end to end.
• If 2 ohms or greater, repair the open/high resistance in the circuit.
• If less than 2 ohms, replace the K9 body control module.
• If the test lamp is always ON
1. Ignition OFF, disconnect the X5 harness connector at the K9 body control module.
2. Test for infinite resistance between the control circuit terminal and ground.
• If less than infinite resistance, repair the short to ground on the circuit.
• If infinite resistance, replace the K9 body control module.
• If the test lamp turns ON and OFF
4. Ignition OFF, connect the X4 harness connector at the X50A fuse block - underhood.
5. Disconnect the harness connector at the appropriate E29 fog lamp, ignition OFF, exterior lamps OFF.
6. Test for less than 5 ohms between the ground circuit terminal B and ground.
• If 5 ohms or greater
1. Ignition OFF.
2. Test for less than 2 ohms in the ground circuit end to end.
• If 2 ohms or greater, repair the open/high resistance in the circuit.
• If less than 2 ohms, repair the open/high resistance in the ground connection.
• If less than 5 ohms
7. Connect a test lamp between the control circuit terminal A and ground, ignition ON.
8. Verify the test lamp turns ON and OFF when commanding the Front Fog Lamps ON and OFF with a scan tool.
• If the test lamp is always OFF
1. Ignition OFF, disconnect the X3 harness connector at the X50A fuse block - underhood.
2. Test for infinite resistance between the control circuit and ground.
• If less than infinite resistance, repair the short to ground on the circuit.
• If infinite resistance
3. Test for less than 2 ohms in the control circuit end to end.
• If 2 ohms or greater, repair the open/high resistance in the circuit.
• If less than 2 ohms, replace the X50A fuse block - underhood.
• If the test lamp is always ON
1. Ignition OFF, disconnect the X3 harness connector at the X50A fuse block - underhood, ignition ON.
2. Test for less than 1 V between the control circuit terminal and ground.
• If 1 V or greater, repair the short to voltage on the circuit.
• If less than 1 V, replace the X50A fuse block - underhood.
• If the test lamp turns ON and OFF
9. Test or replace the appropriate E29 fog lamp.
Front Fog Lamp Indicator Malfunction
1. Ignition ON.
2. Verify the front fog lamp indicator turns ON and OFF when commanding the Instrument Cluster All Indicators Test ON and OFF with a scan tool.
• If the front fog lamp indicator is always OFF or remains ON
Replace the P16 instrument cluster.
• If the front fog lamp indicator turns ON and OFF
3. Replace the K9 body control module.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the repair.
* Front Fog Lamp Replacement (Equinox) Service and RepairFront Fog Lamp Replacement (Terrain) Service and Repair
* Turn Signal Multifunction Switch Replacement Turn Signal Multifunction Switch Replacement
* Accessory Wiring Junction Block Replacement Accessory Wiring Junction Block Replacement
* Control Module References Programming and Relearning for BCM or instrument cluster replacement, programming, and setup