Cylinder Head Replacement - Right Side
Cylinder Head Replacement - Right Side
Special Tools
* J 45059 Angle Meter
* J 42385-200 Common Thread Repair Kit
Removal Procedure
1. Remove the oil level indicator. Refer to Oil Level Indicator Tube Replacement Service and Repair.
2. Remove the intake manifold. Refer to Intake Manifold Replacement (RPOs LY2, LY6) Service and RepairIntake Manifold Replacement (RPOs LC9, LMG, LY5, L76) Service and RepairIntake Manifold Replacement (Except RPOs LY2, LY6, LC9, LMG, LY5) Service and Repair.
3. Remove the coolant air bleed pipe. Refer to Engine Coolant Air Bleed Pipe Replacement (without AFM) Engine Coolant Air Bleed Pipe Replacement (without AFM)Engine Coolant Air Bleed Pipe Replacement (with AFM) Engine Coolant Air Bleed Pipe Replacement (with AFM).
4. Remove the right exhaust manifold. Refer to Exhaust Manifold Replacement - Right Side Exhaust Manifold Replacement - Right Side.
5. Remove the pushrods. Refer to Valve Rocker Arm and Push Rod Replacement Service and Repair.
6. Remove the negative battery cable stud (1) from the front of the right cylinder head.
7. Remove the negative battery cable terminal (2) and the engine harness terminal (3) from the cylinder head.
Note: The cylinder head bolts are of a torque-to-yield design and are NOT to be reused.
8. Remove and discard the cylinder head bolts (220, 221).
Caution: After removal, place the cylinder head on 2 wood blocks in order to prevent damage to the sealing surfaces.
9. Remove the cylinder head (218).
10. Remove and discard the cylinder head gasket (217).
11. If required, clean and inspect the cylinder head. Refer to Cylinder Head Cleaning and Inspection 52. Cylinder Head Cleaning and Inspection.
Installation Procedure
Warning
Wear safety glasses in order to avoid eye damage.
Caution: Clean all dirt, debris, and coolant from the engine block cylinder head bolt holes. Failure to remove all foreign material may result in damaged threads, improperly tightened fasteners or damage to components.
Note: If installing a new cylinder head it is necessary to install a new engine coolant air bleed plug into the rear coolant passage of the cylinder head. Refer to Cylinder Head Assemble 54. Cylinder Head Assemble.
Note:
* Do not reuse the cylinder head bolts. Install NEW cylinder head bolts during assembly.
* Do not use any type of sealant on the cylinder head gasket (unless specified).
1. Clean the engine block cylinder head bolt holes, if required. Thread repair tool J 42385-107, found in J 42385-200 may be used to clean the threads of old threadlocking material.
2. Spray cleaner GM P/N 12346139, P/N 12377981 (Canadian P/N 10953463), or equivalent into the hole.
3. Clean the cylinder head bolt holes with compressed air.
4. Check the cylinder head locating pins for proper installation (a) 8.3 mm (0.327 in).
Note: When properly installed, with FRONT on the right side, the tab on the cylinder head gasket should be located right of center.
5. Install the NEW cylinder head gasket (217) onto the locating pins.
6. Install the cylinder head (218) onto the locating pins.
7. Install the NEW cylinder head bolts (220, 221).
Caution: Refer to Fastener Caution Fastener Caution.
8. Tighten the cylinder head bolts.
1. Tighten the M11 cylinder head bolts (1-10) a first pass in sequence to 30 Nm (22 lb ft).
2. Tighten the M11 cylinder head bolts (1-10) a second pass in sequence to 90 degrees using J 45059 .
3. Tighten the M11 cylinder head bolts (1-10 ) a final pass to 70 degrees in sequence using J 45059 .
4. Tighten the M8 cylinder head bolts (11-15) to 30 Nm (22 lb ft). Begin with the center bolt (11) and alternating side-to-side, work outward tightening all of the bolts.
9. Ensure that the engine harness terminal (3) is positioned behind the negative battery cable terminal (2).
10. Position the negative battery cable terminal (2) to the cylinder head.
11. Install the negative battery cable stud (1) to the front of the right cylinder head and tighten the stud to 25 Nm (18 lb ft).
12. Install the pushrods. Refer to Valve Rocker Arm and Push Rod Replacement Service and Repair.
13. Install the right exhaust manifold. Refer to Exhaust Manifold Replacement - Right Side Exhaust Manifold Replacement - Right Side.
14. Install the coolant air bleed pipe. Refer to Engine Coolant Air Bleed Pipe Replacement (without AFM) Engine Coolant Air Bleed Pipe Replacement (without AFM)Engine Coolant Air Bleed Pipe Replacement (with AFM) Engine Coolant Air Bleed Pipe Replacement (with AFM).
15. Install the intake manifold. Refer to Intake Manifold Replacement (RPOs LY2, LY6) Service and RepairIntake Manifold Replacement (RPOs LC9, LMG, LY5, L76) Service and RepairIntake Manifold Replacement (Except RPOs LY2, LY6, LC9, LMG, LY5) Service and Repair.
16. Install the oil level indicator. Refer to Oil Level Indicator Tube Replacement Service and Repair.