Relays, Sensors, and Control Systems
PGM-FI SystemThe Programmed Fuel Injection (PGM-FI) system is a sequential multi port fuel injection system.
Alternator Control
The alternator signals the ECM during charging. The ECM then controls the voltage generated at the alternator according to the electrical load determined by the ELD (Electrical Load Detector) and driving mode. This reduces engine load to improve fuel economy.
A/C Switch
The A/C (air conditioning) switch signals the ECM whenever there is a demand for cooling.
A/C Compressor Clutch Relay
When the ECM receives a demand for cooling from the A/C system, it delays the compressor from being energized, and enriches the mixture to assure smooth transition to the A/C mode.
Barometric Pressure (BARO) Sensor
The LC sensor is inside the ECM. It converts atmospheric pressure into a voltage signal that modifies the basic duration of the fuel injection discharge.
Crankshaft Position (CKP) Sensor
The CKP sensor determines timing for injection of each cylinder and also detects engine speed.
Engine Coolant Temperature (ECT) Sensor
The ECT sensor is a temperature dependent resistor (thermistor). The resistor of the thermistor decreases as the engine coolant temperature increases.
Intake Air Temperature (IAT) Sensor
The IAT sensor is a temperature dependent resistor (thermistor). The resistance of the thermistor decreases as the intake air temperature increases.
Injector Timing and Duration
The ECM contains the memory for basic discharge duration at various engine speeds and manifold pressures. The basic discharge duration, after being read out from the memory, is further modified by signals sent from various sensors to obtain the final discharge duration.
By monitoring Long Term Fuel Trim, the ECM detects long term malfunctions in the fuel system, and will set a DTC if the malfunction occurs during two consecutive trips.
Ignition Timing Control
The ECM contains the memory for basic ignition timing at various engine speeds and manifold air flow rates. It also adjusts the timing according to engine coolant temperature. The ECM detects misfiring by using the CKP sensor to monitor fluctuations in crankshaft speed. It will then set DTCs depending on how much misfiring occurs.
Knock Sensor
The knock control system adjusts the ignition timing to minimize knock.
Manifold Absolute Pressure (MAP) Sensor
The MAP sensor converts manifold absolute pressure into electrical signals to the ECM.
Primary and Secondary Heated Oxygen Sensors (HO(2)S)
The heated oxygen sensors detect the oxygen content in the exhaust gas, then sends signal to the ECM which varies the duration of injection accordingly. To stabilize its output, the sensors have an internal heater. The primary sensor is installed in the exhaust pipe. The secondary sensor is installed in the TWC.
By controlling the air/fuel ratio with sensors, the deterioration of the primary sensor can be evaluated by its feedback period. When the feedback period exceeds a certain value during stable driving conditions, the sensor is considered deteriorated and the ECM sets a DTC.
Starting Control
When the engine is started, the ECM provides a rich mixture by increasing injector duration.
Throttle Position (TP) Sensor
The TP sensor is a potentiometer connected to the throttle valve shaft. As the throttle position changes, the sensor varies the signal voltage to the ECM. The TP sensor is not replaceable apart from the throttle body.
[1][2]Top Dead Center (TDC) Sensors
The TDC1/TDC2 sensor determines ignition timing at start up (cranking) and when crank angle is abnormal.
Idle Control System
When the engine is cold, the A/C compressor is on, the transmission is in gear, the brake pedal is pressed, the P/S load is high, or the alternator is charging, the ECM controls current to the IAC valve to maintain the correct idle speed. Refer to the System Diagram to see the functional layout of the system.
Brake Pedal Position Switch
The brake pedal position switch signals the ECM when the brake pedal is pressed.
Electrical Power Steering (EPS) Signal
The EPS signals the ECM when the power steering load is high.
Engine Start Switch
The engine start switch signals the ECM when the engine is cranking.
Idle Air Control (IAC) Valve
To maintain the proper idle speed, the IAC valve changes the amount of air bypassing the throttle body in response to an electrical signal from the ECM.