Repair Procedures

Removal

Smart Key Unit
1. Disconnect the negative (-) battery terminal.
2. Remove the console under cover( A) and connectors(B).




3. After loosening the console mounting screws, remove the floor console assembly (A).




4. After loosening the smart key unit mounting bolts(B) and connector, remove the smart key unit (A).

RF Receiver
1. Disconnect the negative (-) battery terminal.
2. Remove the glove box.




3. After loosening the mounting screws and bolts, then remove the glove box housing (A).
Disconnect the connector (B).




4. After loosening the mounting nuts(2EA), then remove the connector.





Interior 1 Antenna
1. Disconnect the negative (-) battery terminal.
2. Remove the console under cover(A) and connectors(B).




3. After loosening the console mounting screws, remove the floor console assembly (A).




4. After loosening the antenna nuts(2EA) and connector, remove the interior 1 antenna (A).





Interior 2 Antenna
1. Disconnect the negative (-) battery terminal.
2. Remove the console rear cover(A) and connectors.




3. After loosening the console mounting screws, remove the floor console assembly (A).




4. After loosening the antenna bolts(2EA) and connector, remove the interior 2 antenna (A).





Interior 3 Antenna
1. Disconnect the negative (-) battery terminal.
2. After loosening the mounting bolts, then remove the third seat assembly(A).




3. After loosening the antenna nuts(2EA) and connector(A), remove the interior 3 antenna (B).





Exterior Bumper Antenna
1. Disconnect the negative (-) battery terminal.
2. Remove the rear bumper.
3. After loosening the antenna connector(A) on the right side of rear bumper and nuts(2EA), remove the interior exterior bumper antenna (b).





Buzzer
1. Disconnect the negative (-) battery terminal.
2. Remove the buzzer(A) in the clip hole after disconnecting the connector on the side rail panel





Door Outside Handle
1. Disconnect the negative (-) battery terminal.
2. Disconnect the connector after removing the door trim.
3. After loosening the mounting bolt and cap(A), then remove the key holder (B).




4. Remove the outside handle (A) by sliding it rearward.





Tailgate Switch
1. Disconnect the negative (-) battery terminal.
2. Remove the tailgate trim.
3. Disconnect the connector (A). After loosening the remove tailgate garnish mounting nuts, then tailgate garnish (B).




4. Remove the outside handle (A) after loosening the outside handle mounting screws.






Installation

Smart Key Unit
1. Install the smart key unit.
2. Install the smart key unit mounting bolt and connector.
3. Install the console assembly.
4. Install the console under cover after connecting the connector.
5. Install the negative (-) battery terminal and check the smart key system.

RF Receiver
1. Install the RF receiver.
2. Install the glove box housing.
3. Install the glove box.
4. Install the negative (-) battery terminal and check the smart key system.

Interior 1 Antenna
1. Install the interior 1 antenna.
2. Install the console assembly.
3. Install the console under cover after connecting the connector.
4. Install the negative (-) battery terminal and check the smart key system.

Interior 2 Antenna
1. Install the interior 2 antenna.
2. Install the connector mounting bracket.
3. Install the console assembly.
4. Install the console rear cover after connecting the connector.
5. Install the negative (-) battery terminal and check the smart key system.

Interior 3 Antenna
1. Install the interior 3 antenna.
2. Install the connector mounting bracket.
3. Install the third seat assembly.
4. Install the negative (-) battery terminal and check the smart key system.

Exterior Bumper Antenna
1. Install the Exterior bumper antenna.
2. Install the rear bumper.
3. Install the negative (-) battery terminal and check the smart key system.

Buzzer
1. Install the buzzer.
2. Install the negative (-) battery terminal and check the smart key system.

Door Outside Handle
1. Install the outside handle.
2. Install the door trim.
3. Install the negative (-) battery terminal and check the smart key system.

Tailgate Switch
1. Install the tailgate switch.
2. Install the tailgate garnish.
3. Install the tailgate trim.
4. Install the negative (-) battery terminal and check the smart key system.