Procedure
NOTE:Verify that the vehicle is affected by accessing Hyundai Motor America's "Warranty Vehicle Information" screen via DCS interactive or DCS on-line to identify an open TIS Campaign on the vehicle.
IMPORTANT PREPARATION BEFORE STARTING REPROGRAMMING:
1. Turn off all lights (do not leave headlight switch in auto mode) and all accessories (including heater/AC/blower, radio, heated seats, rear defogger, etc.) to make certain the battery will not be discharged during reprogramming.
2. If the vehicle was in storage, you must START and RUN the engine for at least 10 minutes before reprogramming to assure there will be adequate stabilized vehicle battery voltage required for a successful reprogram. Battery voltage must remain above 11.0V for the duration of 20-25 minutes of reprogram.
CAUTIONS DURING REPROGRAMMING:
1. Perform reprogramming with the ignition key in the ON position.
2. Be careful not to disconnect the Hi-Scan Pro during reprogramming.
3. Do not start the engine during reprogramming.
4. Do not turn the ignition key OFF during reprogramming.
5. When the reprogramming is completed, turn the ignition key OFF then wait for about 20 seconds. Start the engine and confirm normal operation of the vehicle.
PCM REPROGRAMMING PROCEDURE:
NOTE:
Verify that the vehicle is within the affected production date and VIN range.
HI-SCAN PRO INSTALLATION PROCEDURE
1. Attach the Data Link Connector (DLC) cable to the Hi-Scan Pro main body and securely tighten the two bolts.
2. Remove the system software card from the Hi-Scan pro and insert the black 32 MB reprogramming software card into the Hi-Scan top slot.
3. Connect the DLC cable from the Hi-Scan Pro into the data link connector (16 Pin connector).
NOTE:
Route the cable over the steering column to ensure the cable does not become disconnected.
AUTOMATIC REPROGRAMMING
PROCEDURE:
1. Turn the ignition switch to the ON position. (Do not start the engine)
2. Turn the Hi-Scan Pro ON and press ENTER.
3. Select option "70. NF 3.3 DRIVING FEEL IMPROVEMENT" and press ENTER.
4. Select option "01. NF 3.3 DRIVING FEEL [AUTO]" and press ENTER.
5. Enter "1229" as the password for automatic reprogramming mode and press ENTER.
6. The Hi-Scan Pro will establish communication, check the PCM ID, and reprogram the PCM automatically.
NOTE:
^ The Hi-Scan Pro detects the current PCM ID, assigns the new PCM ID and displays them on the Hi-Scan Pro screen.
^ Check the PCM ID displayed on the Hi-Scan Pro screen to verify that the correct PCM software is being downloaded (NF5N33*S2AS5E1BC).
WARNING:
Do not interrupt the reprogramming at any time.
^ If the Hi-Scan Pro does not download the program, use the "MANUAL REPROGRAMMING PROCEDURE" following this section.
7. When "REPROGRAMMING COMPLETED" message is displayed, turn the Hi-Scan Pro OFF.
8. Turn the ignition key OFF for about 20 seconds and start the engine to confirm proper operation of the vehicle.
9. Check for diagnostic trouble codes using the Hi-Scan Pro with the system software card and erase any trouble codes.
MANUAL REPROGRAMMING PROCEDURE:
1. Turn the ignition switch to the OFF position.
2. Pull out the ECU fuse # 16 (10A) from the engine room relay box for 15 seconds and then reinstall it.
3. Turn the ignition switch to the ON position. (Do not start the engine)
4. Turn the Hi-Scan Pro ON and press ENTER.
5. Select option "70. NF 3.3 DRIVING FEEL IMPROVEMENT" and press ENTER.
6. Select option "02. NF 3.3 DRIVING FEEL [ERROR]" and press ENTER.
7. Select 39110-3C760 and press ENTER.
8. Enter the password (3760) and press ENTER.
9. The Hi-Scan Pro will establish communication, check the PCM ID, and reprogram the PCM automatically.
NOTE:
^ The Hi-Scan Pro detects the current PCM ID, assigns the new PCM ID and displays them on the Hi-Scan Pro screen.
^ Check the PCM ID displayed on the Hi-Scan Pro screen to verify that the correct PCM software is being downloaded (NF5N33*S2AS5E1BC).
WARNING:
Do not interrupt the reprogramming at any time.
10. When "REPROGRAMMING COMPLETED" message is displayed, turn the Hi-Scan Pro OFF.
11. Turn the ignition key OFF for about 20 seconds and start the engine to confirm proper operation of the vehicle.
12. Check for diagnostic trouble codes using the Hi-Scan Pro with the system software card and erase any trouble codes.
CAMPAIGN CLAIM INFORMATION