B2502
DTC B2502 PASSENGER TELLTALE LAMP (PR0HIBITED) FAILUREDTC DESCRIPTION
The Telltale Lamp circuit consists of the Telltale Lamp and the SRSCM. SRSCM set the above DTC that the Telltale Lamp, failure is detected.
DTC Detecting Condition:
Schematic Diagram:
TERMINAL & CONNECTOR INSPECTION
1. Visually inspect all connectors related to the affected circuit for damage and secure connection.
2. Inspect terminals for damage and corrosion.
CAUTION: Avoid damaging connectors during the inspection process.
3. Are any problems found?
NO - Go to next step.
YES - After repairing the trouble part, check whether DTC occurs or not.
INSPECTION PROCEDURE
1. PREPARATION
1. Turn the ignition switch to LOCK.
2. Disconnect the negative (-) terminal from the battery and wait for at least 3 minutes.
3. Remove the DAB module and disconnect the DAB connector.
4. Disconnect the connectors of the PAB, SAB, CAB, BPT, BUPT, FIS and SIS.
5. Disconnect the SRSCM connector.
2. CHECK THE FUSE
1. Remove the airbag fuse and the airbag telltale lamp fuse from junction block.
2. Inspect the fuses.
Are the fuses normal?
YES - Check the telltale lamp bulb.
NO - Repair or replace the fuses.
3. CHECK THE TELLTALE LAMP BULB
1. Remove the bulb from the instrument cluster.
2. Inspect the bulb.
Is the bulb normal?
YES - Check source voltage.
NO - Repair or replace the bulb.
4. CHECK SOURCE VOLTAGE
1. Connect the negative (-) terminal to the battery.
2. Turn the ignition switch to ON.
3. Measure voltage between the terminal 1 of the Telltale Lamp harness connector and chassis ground(-).
Specification (Voltage): 9 - 16 V
4. Is the measured voltage within specification?
YES - Check short to battery line.
NO - Repair or replace the wiring harness between ignition switch and the Telltale Lamp.
5. CHECK SHORT TO BATTERY LINE
1. Measure voltage between the terminal 4 of the Telltale Lamp harness connector and chassis ground(-).
Specification (voltage) : Approximately 0 V
2. Is the measured voltage within specification?
YES - Check short or short to ground.
NO - Repair the short to battery line circuit on wiring harness between the SRSCM and the Telltale Lamp.
6. CHECK SHORT OR SHORT TO GROUND
1. Turn the ignition switch to LOCK.
2. Disconnect the negative (-) terminal from the battery.
3. Measure resistance between the terminal 4 of the Telltale Lamp harness connector and chassis ground.
4. Measure resistance between the terminal 1 and 4 of the Telltale Lamp harness connector.
Specification (resistance) : infinite
5. Is the measured resistance within specification?
YES - Check open circuit.
NO - Repair the short or short to ground circuit on wiring harness between the SRSCM and the Telltale Lamp.
7. CHECK OPEN CIRCUIT
1. Measure resistance between the terminal 4 of the Telltale Lamp harness connector and the terminal 18 (A) of SRSCM harness connector.
Specification (resistance) : below 1 ohm
2. Is the measured resistance within specification?
YES - Go to next step.
NO - Repair the open circuit on wiring harness between the SRSCM and the Telltale Lamp.
8. CLEAR THE DTC AND CHECK THE VEHICLE AGAIN
1. Install the DAB module and connect the DAB connector.
2. Connect the connectors of the PAB, SAB, CAB, BPT, BUPT, FIS and SIS.
3. Connect the SRSCM connector.
4. Connect the negative (-) terminal to the battery.
5. Connect a Hi-Scan (Pro) to the data link connector.
6. Turn the ignition switch to ON.
7. Clear the DTC stored in the SRSCM memory with the Hi-Scan (Pro).
8. Turn the ignition switch to LOCK and wait for at least 30 seconds.
9. Turn the ignition switch to ON and wait for at least 30 seconds.
10. Check the vehicle again with the Hi-Scan (Pro).
Does the above DTC(s) go off?
YES - Problem is intermittent or was repaired and SRSCM memory was not cleared.
NO - Replace the SRSCM with a new one, and then check the vehicle again. At this time, if the vehicle normally operates with a new SRSCM, the fault may be the SRSCM (Replace SRSCM).