P0760
DTC P0760 SHIFT CONTROL SOLENOID VALVE C CIRCUIT MALFUNCTIONCOMPONENT LOCATION
Refer to DTC P0741. P0741
GENERAL DESCRIPTION
Refer to DTC P0750. P0750
DTC DESCRIPTION
Refer to DTC P0750. P0750
DTC DETECTING CONDITION
DTC DETECTING CONDITION:
SPECIFICATION
Refer to DTC P0743. P0743
SCHEMATIC DIAGRAM
Refer to DTC P0741. P0741
MONITOR SCAN TOOL DATA
1. Connect SCAN TOOL to data link connector (DLC)
2. Engine ON.
3. Monitor the 2nd SOL. VALVE parameter on the SCAN TOOL.
4. Shift gear position 1st to 2nd.
Specification: 1st gear - 100%, 2nd gear - 0.0%
Specification:
5. Does 2nd SOLENOID DUTY follow the reference data?
YES > Fault is intermittent caused by poor contact in the sensor's and/or TCM (PCM)'s connector or was repaired and TCM (PCM) memory was not cleared. Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration or damage. Repair or replace as necessary and go to Verification of Vehicle Repair procedure.
NO > Go to Terminal & Connector Inspection procedure.
TERMINAL & CONNECTOR INSPECTION
Refer to DTC P0743. P0743
POWER SUPPLY CIRCUIT INSPECTION
1. Disconnect A/T SOLENOID VALVE connector.
2. Measure voltage between terminal 5 of the sensor harness connector and chassis ground.
3. Turn ignition switch OFF - ON
Specification: 12 V is measured only for approximately 0.5 sec
Specification:
4. Is voltage within specifications?
YES > Go to Signal circuit inspection procedure.
NO > Check that A/T-30A Fuse in engine room junction is installed or not blown. Check for open in harness. Repair as necessary and go to Verification of Vehicle Repair procedure.
SIGNAL CIRCUIT INSPECTION
1. Check signal circuit open inspection
1. Ignition OFF.
2. Disconnect A/T SOLENOID VALVE connector and TCM (PCM) connector
3. Measure resistance between terminal 4 of the ATM SOLENOID VALVE harness connector and terminal 17 of the TCM (PCM) harness connector
Specification: approximately 0 Ohms
Specification:
4. Is resistance within specifications?
YES > Go to Check signal circuit short inspection procedure.
NO > Check for open in harness. Repair as necessary and go to Verification of Vehicle Repair procedure.
2. Check signal circuit short inspection
1. Ignition OFF.
2. Disconnect A/T SOLENOID VALVE connector and TCM (PCM) connector.
3. Measure resistance between terminal 4 of the ATM SOLENOID VALVE harness and chassis ground.
Specification: Infinite
Specification:
4. Is resistance within specifications?
YES > Go to Component Inspection procedure.
NO > Check for short to ground in harness. Repair as necessary and go to Verification of Vehicle Repair procedure.
COMPONENT INSPECTION
1. CHECK SOLENOID VALVE
1. Ignition OFF.
2. Disconnect A/T SOLENOID VALVE connector.
3. Measure resistance between terminal 4 and terminal 5 of the ATM SOLENOID VALVE harness connector.
Specification: Approximately 2.7 - 3.4 Ohms [20°C (68°F)]
Specification:
4. Is resistance within specification?
YES > Go to CHECK TCM (PCM).
NO > Replace 2nd SOLENOID VALVE as necessary and go to Verification of Vehicle Repair procedure.
2. CHECK TCM (PCM)
1. Connect SCAN TOOL to data link connector (DLC)
2. Ignition ON& Engine OFF.
3. Select A/T Solenoid valve Actuator test and Operate Actuator test.
4. Can you hear operating sound for 2ND SOLENOID VALVE Actuator Testing Function?
YES > Go to Verification of Vehicle Repair procedure.
NO > Replace TCM (PCM) and go to Verification of Vehicle Repair procedure.
ACTUATOR TEST CONDITION
1. IG SWITCH ON
2. TRANSAXLE RANGE SWITCH is normal
3. P RANGE
4. Vehicle Speed 0 km/h
5. Throttle position sensor < 1 V
6. IDLE SWITCH ON
7. ENGINE RPM 0
VERIFICATION OF VEHICLE REPAIR
Refer to DTC P0741. P0741