P0765
DTC P0765 SHIFT CONTROL SOLENOID VALVE D CIRCUIT MALFUNCTIONCOMPONENT LOCATION
Refer to DTC P0741. P0741
GENERAL DESCRIPTION
Refer to DTC P0750. P0750
DTC DESCRIPTION
Refer to DTC P0750. P0750
DTC DETECTING CONDITION
DTC DETECTING CONDITION:
SPECIFICATION
Refer to DTC P0743. P0743
SCHEMATIC DIAGRAM
Refer to DTC P0741. P0741
MONITOR SCAN TOOL DATA
1. Connect SCAN TOOL to data link connector (DLC). 2, Engine ON.
3. Monitor the OD SOL. VALVE parameter on the SCAN TOOL.
4. Shift gear position 2nd to 3rd.
Specification: 2nd gear - 100%, 3rd gear - 0.0%
Specification:
Does OD SOLENOID DUTY follow the reference data?
YES > Fault is intermittent caused by poor contact in the sensor's and/or TCM (PCM)'s connector or was repaired and TCM (PCM) memory was not cleared. Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration or damage. Repair or replace as necessary and go to Verification of Vehicle Repair procedure.
NO > Go to Terminal & Connector Inspection procedure.
TERMINAL & CONNECTOR INSPECTION
Refer to DTC P0743. P0743
POWER SUPPLY CIRCUIT INSPECTION
1. Disconnect A/T SOLENOID VALVE connector.
2. Measure voltage between terminal 5 of the sensor harness connector and chassis ground.
3. Turn ignition switch OFF -ON.
Specification: 12 V is measured only for approximately 0.5 sec
Specification:
Is voltage within specifications?
YES > Go to Signal circuit inspection procedure.
NO > Check that A/T-30A Fuse in engine room junction is installed or not blown. Check for open in harness. Repair as necessary and go to Verification of Vehicle Repair procedure.
SIGNAL CIRCUIT INSPECTION
1. Check signal circuit open inspection
1. Ignition OFF.
2. Disconnect A/T SOLENOID VALVE connector and TCM (PCM) connector.
3. Measure resistance between terminal 12 of the ATM SOLENOID VALVE harness connector and terminal 16 of the TCM (PCM) harness connector
Specification: approximately 0 Ohms
Specification:
Is resistance within specifications?
YES > Go to Check signal circuit short inspection procedure.
NO > Check for open in harness. Repair as necessary and go to Verification of Vehicle Repair procedure.
2. Check signal circuit short inspection
1. Ignition OFF & Engine OFF.
2. Disconnect A/T SOLENOID VALVE connector and TCM (PCM) connector.
3. Measure resistance between terminal 12 of the ATM SOLENOID VALVE harness and chassis ground.
Specification: Infinite
Specification:
4. Is resistance within specifications?
YES > Go to Component Inspection procedure.
NO > Check for short to ground in harness. Repair as necessary and go to Verification of Vehicle Repair procedure.
COMPONENT INSPECTION
1. CHECK SOLENOID VALVE
1. Ignition OFF.
2. Disconnect A/T SOLENOID VALVE connector.
3. Measure resistance between terminal 12 and terminal 5 of the ATM SOLENOID VALVE harness connector.
Specification: Approximately 2.7 - 3.4 Ohms [20°C (68°F)]
Specification:
4. Is resistance within specification?
YES > Go to CHECK TCM (PCM).
NO > Replace OD SOLENOID VALVE as necessary and go to Verification of Vehicle Repair procedure.
2. CHECK TCM (PCM)
1. Connect SCAN TOOL to data link connector (DLC).
2. Ignition ON & Engine OFF.
3. Select A/T Solenoid valve Actuator test and Operate Actuator test.
4. Can you hear operating sound for OD SOLENOID VALVE Actuator Testing Function?
YES > Go to Verification of Vehicle Repair procedure.
NO > Replace TCM (PCM) and go to Verification of Vehicle Repair procedure.
ACTUATOR TEST CONDITION
1. IG SWITCH ON
2. TRANSAXLE RANGE SWITCH is normal
3. P RANGE
4. Vehicle Speed 0 km/h
5. Throttle position sensor < 1 V
6. IDLE SWITCH ON
7. ENGINE RPM 0
VERIFICATION OF VEHICLE REPAIR
Refer to DTC P0741. P0741