Deployment Procedures For Air Bag Module (Outside of Vehicle)

DEPLOYMENT PROCEDURES FOR AIR BAG MODULE (OUTSIDE OF VEHICLE)




Unless the vehicle is being scrapped deploying the air bag in the vehicle is not recommended.This may cause damage to the vehicle interior.

Anchor air bag module bracket [SST KV99105300 (J41246)] in a vise secured to a firm foundation during deployment.


Deployment of Driver Air Bag Module (Outside of vehicle)




1. Make an 8.5 mm (0.335 in) diameter hole in air bag module bracket [SST KV99105300 (J41246)] at the position shown in figure.




2. Firmly secure air bag module bracket [SST KV99105300 (J41246)] with air bag module attached in a vise.
3. Using wire secure air bag module to air bag module bracket [SST KV99105300 (J41246)] at two places.

CAUTION: Use wire of at least 1 mm (0.04 in) diameter.




4. Connect deployment tool adapter [SST J38381-80] to air bag module connector and deployment tool connector [SST KV9910400 (J38381)].




5. Connect red clip of deployment tool to battery positive terminal and black clip to negative terminal.
6. The lamp on the right side of the tool, marked deployment tool power", should glow green, not red.
7. Press the button on the deployment tool.The left side lamp on the tool, marked air bag connector voltage", will illuminate and the air bag module will deploy.

CAUTION: When deploying the driver air bag module, stand at least 5 m (16 ft) away from the air bag module.

Deployment of Front Passenger Air Bag Module (Outside of vehicle)




1. Firmly secure air bag module bracket [SST KV99105300 (J41246)] in a vise.




2. Match the hole in air bag module bracket (held in vise) and front passenger air bag module and fix them with one bolt [M8 x 25 - 30 mm (0.98 - 1.18 in)].




3. Connect deployment tool [SST KV99106400 (J38381)] and deployment tool adapter (SST J38381-65) to front passenger air bag module connector.
4. Connect red clip of deployment tool to battery positive terminal and black clip to negative terminal.
5. The lamp on the right side of the tool, marked "deployment tool power", should glow green, not red.




6. Press the button on the deployment tool.The left side lamp on the tool, marked "air bag connector voltage", will illuminate and the air bag module will deploy.

CAUTION:
- When deploying the front passenger air bag module, do not stand on the deploying side.
- Stand at least 5 m (16 ft) away from the air bag module.

Deployment of Front Side Air Bag Module (Outside of vehicle)




1. Make 6.5 mm (0.256 in) diameter holes in air bag module bracket [SST KV99105300 (J41246)] at the position shown in figure.




2. Firmly secure air bag module bracket [SST KV99105300 (J41246)] in a vise.
3. Insert the stud bolts of side air bag module into the two holes in air bag module bracket (held in vise) and fix them with two M6 nuts.

CAUTION: Side air bag module should be secured to air bag module bracket [SST: KV99105300 (J41246)] in a vise with stud bolt side facing down.




4. Connect deployment tool adapter [SST KV99108300 (J38381-35)] and deployment tool [SST KV99106400 (J38381)] on side air bag module.




5. Connect red clip of deployment tool to battery positive terminal and black clip to negative terminal.
6. The lamp on the right side of the tool, marked "deployment tool power", should glow green, not red.
7. Press the button on the deployment tool. The left side lamp on the tool, marked "air bag connector voltage", will illuminate and the air bag module will deploy.

CAUTION: When deploying the front side air bag module, stand at least 5 m (16 ft) away from the air bag module.

Deployment of Side Curtain Air Bag Module (Outside of vehicle)




1. Cut the inflator from side curtain air bag module.




2. Connect deployment tool [SST KV99106400 (J38381)] and deployment tool adapter yellow connector [SST J38381-80] to the inflator.




3. Put the inflator connected with the deployment tool [SST KV99106400 (J38381)] into a tire without a wheel.




4. Put the tire with the inflator onto another tire without wheel.Add an additional tire without a wheel and then a tire mounted on a wheel on top.

CAUTION: Tie all tires together with a strap in order keep them standing.

5. Connect red clip of deployment tool to battery positive terminal and black clip to negative terminal.
6. The lamp on the right side of the tool, marked "deployment tool power", should glow green, not red.
7. Press the button on the deployment tool. The left side lamp on the tool, marked "air bag connector voltage", will illuminate and the air bag module will deploy.

CAUTION: When deploying the side curtain air bag module, stand at least 5 m (16 ft) away from the side cur tam air bag module.