Function of Center Switch
FUNCTION OF CENTER SWITCH
Display with Pushed "DEST" button
- Easy Mode
- Expert Mode
Display with Pushed "ROUTE" button
- Easy Mode
- Expert Mode
Display with Pushed "SETTING" button
The function of each icon is as shown:
Display Settings
How To Perform Display Setting
1. Start the engine.
2. Push "SETTING" button.
3. Select "Display".
4. Push "Enter" switch.
Application Item:
Application Items
Brightness/Contrast/Map Back ground
Select "Brightness/Contrast/Map Background".
- Brightness, Contrast and Back ground are shown at the lower part of the screen, and it can be set by pushing joystick.
Display Off
Select "Display Off".
- When setting is turned on (Indicator light ON), the display will be under sleep mode.
Setting of the Under Section Display
Select "Setting of the under section display".
- The setting status that is selected from A/C or AV is shown at the lower part of the screen.
Vehicle Electronic Systems
How To Perform Vehicle Electronic Systems
1. Start the engine.
2. Push "SETTING" button.
3. Select "Vehicle Electronic Systems".
4. Push "Enter" switch.
Application Items:
Application Items
Adjust Driver Seat When Exiting Vehicle
1. Select "Adjust Driver Seat When Exiting Vehicle".
2. Push "Enter" switch.
- The indicator light alternately turns on and off each time the "Enter" switch is pressed.
Lift Steering Column When Exiting Vehicle
1. Select "Lift Steering Column When Exiting Vehicle".
2. Push "Enter" switch.
- The indicator light alternately turns on and off each time the "Enter" switch is pressed.
Selective Door Unlock (With Intelligent Key)
1. Select "Selective Door Unlock".
2. Push "Enter" switch.
- The indicator light alternately turns on and off each time the "Enter" switch is pressed.
Keyless Remote Response-Horn
1. Select "Keyless Remote Response-Horn".
2. Push "Enter" switch.
- The indicator light alternately turns on and off each time the "Enter" switch is pressed.
Keyless Remote Response-Lights
1. Select "Keyless Remote Response-Light".
2. Push "Enter" switch.
Auto Re-Lock Time
1. Select "Auto Re-Lock Time".
2. Move the joystick and push "Enter" switch to adjust the time.
Sensitivity of Automatic Headlights
1. Select "Sensitivity of Automatic Headlights".
2. Move the joystick to left (lower) or right (higher) and push "Enter" switch.
Automatic Headlights Off Delay
1. Select "Automatic Headlights Off Delay".
2. Move the joystick left or right to adjust the timer and push "Enter" switch.
Speed Dependent Wiper
1. Select "Speed Dependent Wiper".
2. Push "Enter" switch.
- The indicator light alternately turns on and off each time the "Enter" switch is pressed.
Intelligent Key Lock Response-Sound
1. Select "Intelligent Key Lock Response-Sound".
2. Push "Enter" switch to change the sound pattern.
Intelligent Key Unlock Response-Beep Sound
1. Select "Intelligent Key Unlock Response-Sound".
2. Push "Enter" switch to change the sound pattern.
Intelligent Key Engine Start Function
1. Select "Intelligent Key Engine Start Function".
2. Push "Enter" switch.
- The indicator light alternately turns on and off each time the "Enter" switch is pressed.
Intelligent Key Lock/Unlock Function
1. Select "Intelligent Key Lock/Unlock".
2. Push "Enter" switch.
- The indicator light alternately turns on and off each time the "Enter" switch is pressed.
Return All Settings to Default
1. Select "Return All Settings to Default".
2. Push "Enter" switch.
- The indicator light alternately turns on and off each time the "Enter" switch is pressed.
System Settings
How To Perform System Settings
1. Start the engine.
2. Push "SETTING" button.
3. Select "System Settings".
Application Items:
Application Items
Language Setting
Select "Language/Unit".
- Language setting can be switched.
- Unit setting can be changed.
Beep Setting
Select "Beep Setting".
- When Beep Setting is on (indicator light on), a beep will sound if the button is pushed.
NOTE: Items in exception of Beep Setting ON/OFF.
- An error beep.
- An interrupted-screen beep.
Navigation Settings
How To Perform Navigation Settings
1. Start the engine.
2. Push "SETTING" button.
3. Select "Navigation".
Application Items:
Application Items
"VIEW" MODE
- To open the map screen display with Birdview(TM), select "Birdview (TM)".
- To open the map screen display with Plan View, select "Plan View".
"HEADING" MODE
- To display north heading, select "North up".
- To display the actual driving direction of the vehicle, select "Heading up".
"NEARBY DISPLAY ICONS" MODE
- Select an icon to display on the map screen.
"SAVE CURRENT LOCATION" MODE
- The current vehicle location can be registered in "Address Book".
NOTE: "Address Book" can store 50 items max.
"ADJUST CURRENT LOCATION" MODE
1. Select an icon"right" or "left" to calibrate the heading direction. (Arrow marks will rotate corresponding to the calibration key.)
2. Select "Set". Then the vehicle mark will be matched to the arrow mark.
"AUTO RE-ROUTE" MODE
- To activate "AUTO RE-ROUTE" mode, select "On".
- To inactivate "AUTO RE-ROUTE" mode, select "Off".
"AVOID AREA SETTING" MODE
- Areas to avoid can be registered.
"CLEAR MEMORY" MODE
- To delete all the stored places in "Address Book", "Avoid Area" and "Previous Destinations", select "Yes".
"EDIT ADDRESS BOOK" MODE
- Edit the items registered in Address Book.
"GPS INFORMATION" MODE
- Latitude, longitude, altitude, receiving state (telemetry), and satellite location are displayed as GPS information.
NOTE: Altitude is displayed only in three-dimensional status.
"QUICK STOP CUSTOMER SETTING" MODE
- Select a category for the "Quick Stop" menu.
"SET AVERAGE SPEED" MODE
- Set the average vehicle speed to calibrate the estimated journey time for the destination.
- Set three items; "Freeway", "Main Roads", and "Ordinary Roads".
"TRACKING" MODE
- To delete the tracking marks on the map, select "Off".
- To leave the tracking marks on the map, select "On".
NOTE: When a trail display is turned OFF, trail data is erased from the memory.
GUIDANCE VOLUME
Description
Following guidance volume setting can be changed.
Activation/Deactivation Setting
- The voice prompt can be turned on/off by pressing the "Guidance Volume" button.
Voice Volume Setting
- Volume of the voice can be controlled by bending the joystick to left/right.
DISPLAY WITH PUSHED "TRIP" BUTTON
- When the "TRIP" button is pushed, the following models will display on the screen.
- Warning message (if there are any)
- TRIP1-> TRIP2-> FUEL ECONOMY-> MAINTENANCE-> OFF.
TRIP 1 OR TRIP 2
- Elapsed time, Driving distance and Average speed are displayed as Trip 1 information or Trip 2 information.
- The way to reset is by pushing the "Reset" switch or by keeping pushing "TRIP" button more than 1.5 seconds.
FUEL ECONOMY
- Average Fuel Economy, Distance to Empty, Fuel Economy are displayed as Fuel Economy information.
- The way to reset is by pushing the "Reset" switch or by keeping pushing "TRIP" button more than 1.5 seconds.
MAINTENANCE
- Engine Oil, Tire Rotation and Tire Pressure are displayed as Maintenance information.
NOTE: In a case of a vehicle with Low tire pressure warning control unit, "Tire Pressure" switch is displayed.
ENGINE OIL OR TIRE ROTATION
- Possible to set up interval of engine oil and tire rotation by moving joystick right and left.
TIRE PRESSURE
- Pressure indication in psi on the screen indicates that the pressure is being measured. After a few driving trips, the pressures for all four tires will be displayed.
- The order of tire pressure figures displayed on the screen does not correspond with the actual order of the tire position.
- Tire pressure rises and falls depending on the heat caused by the vehicle's traveling condition and the temperature.
- In case of low tire pressure, the low tire pressure warning light will come on and/or a warning is displayed on the screen.
- FLAT TIRE-very low tire air pressure.
NOTE:
- In a case of FLAT TIRE pressure, interrupt screen is not shown on the display.
- On the screen of TIRE PRESSURE, "FLAT TIRE", "Check", "All tire" is displayed.
WARNING INDICATIONS
Warning signal (door switch signal) is received from BCM through CAN communication line.