Cruise Test Part 1
Cruise Test - Part 11. CHECK STARTING OUT FROM D1
1. Drive the vehicle for about 10 minutes to warm up the engine oil and A/T fluid.
Appropriate temperature for the A/T fluid: 50 - 80°C (122 - 176°F)
2. Park the vehicle on a level surface.
3. Move selector lever to "P" position.
4. Start the engine.
5. Move selector lever to "D" position.
6. Press the accelerator pedal about half way down to accelerate the vehicle.
With CONSULT-II
Read the gear positions. Refer to "DATA MONITOR MODE".
Starts from D1 ?
YES >> GO TO 2.
NO >> Enter a check mark at "Vehicle Cannot Be Started From D1" on the "DIAGNOSTIC WORKSHEET", then continue the road test.
2. CHECK SHIFT-UP D1 -> D2
Press down the accelerator pedal about half way and inspect if the vehicle shifts up (D1 -> D2) at the appropriate speed.
^ Refer to "Vehicle Speed at Which Gear Shifting Occurs".
With CONSULT-II
Read the gear position, throttle degree of opening, and vehicle speed. Refer to "DATA MONITOR MODE".
Does the A/T shift-up D1 -> D2 at the correct speed?
YES >> GO TO 3.
NO >> Enter a check mark at "A/T Does Not Shift: D1 -> D2" on the "DIAGNOSTIC WORKSHEET", then continue the road test.
3. CHECK SHIFT-UP D2 -> D3
Press down the accelerator pedal about half way and inspect if the vehicle shifts up (D2 -> D3) at the appropriate speed.
^ Refer to "Vehicle Speed at Which Gear Shifting Occurs".
With CONSULT-II
Read the gear position, throttle degree of opening, and vehicle speed. Refer to "DATA MONITOR MODE".
Does the A/T shift-up D2 -> D3 at the correct speed?
YES >> GO TO 4.
NO >> Enter a check mark at "A/T Does Not Shift: D2 -> D3" on the "DIAGNOSTIC WORKSHEET", then continue the road test.
4. CHECK SHIFT-UP D3 -> D4
Press down the accelerator pedal about half way and inspect if the vehicle shifts up (D3 -> D4) at the appropriate speed.
^ Refer to "Vehicle Speed at Which Gear Shifting Occurs".
With CONSULT-II
Read the gear position, throttle degree of opening, and vehicle speed. Refer to "DATA MONITOR MODE".
Does the A/T shift-up D3 -> D4 at the correct speed?
YES >> GO TO 5.
NO >> Enter a check mark at "A/T Does Not Shift: D3 -> D4" on the "DIAGNOSTIC WORKSHEET", then continue the road test.
5. CHECK SHIFT-UP D4 -> D5
Press down the accelerator pedal about half way and inspect if the vehicle shifts up (D4 -> D5) at the appropriate speed.
^ Refer to "Vehicle Speed at Which Gear Shifting Occurs".
With CONSULT-II
Read the gear position, throttle degree of opening, and vehicle speed. Refer to "DATA MONITOR MODE".
Does the A/T shift-up D4 -> D5 at the correct speed?
YES >> GO TO 6.
NO >> Enter a check mark at "A/T Does Not Shift: D4 -> D5" on the "DIAGNOSTIC WORKSHEET", then continue the road test.
6. CHECK LOCK-UP
When releasing accelerator pedal from D5, check lock-up from D5 to L/U.
^ Refer to "Vehicle Speed at Which Gear Shifting Occurs".
With CONSULT-II
Select "TCC SOLENOID" with the "MAIN SIGNAL" mode for "A/T". Refer to "CONSULT-II REFERENCE VALUE".
Does it lock-up?
YES >> GO TO 7.
NO >> Enter a check mark at "A/T Does Not Perform Lock-up" on the AT-47, "DIAGNOSTIC WORKSHEET", then continue the road test. Introduction
7. CHECK LOCK-UP HOLD
Check hold lock-up.
With CONSULT-II
Select "TCC SOLENOID" with the "MAIN SIGNAL" mode for "A/T". Refer to "CONSULT-II REFERENCE VALUE".
Does it maintain lock-up status?
YES >> GO TO 8.
NO >> Enter a check mark at "A/T Does Not Hold lock-up Condition" on the "DIAGNOSTIC WORKSHEET", then continue the road test.
8. CHECK LOCK-UP RELEASE
Check lock-up cancellation by depressing brake pedal lightly to decelerate.
With CONSULT-II
Select "TCC SOLENOID" with the "MAIN SIGNAL" mode for A/T. Refer to "CONSULT-II REFERENCE VALUE".
Does lock-up cancel?
YES >> GO TO 9.
NO >> Enter a check mark at "Lock-up Is Not Released" on the "DIAGNOSTIC WORKSHEET" then continue the road test.
9. CHECK SHIFT-DOWN D5 -> D4
Decelerate by pressing lightly on the brake pedal.
With CONSULT-II
Read the gear position and engine speed. Refer to "DATA MONITOR MODE".
When the A/T shift-down D5 -> D4, does the engine speed drop smoothly back to idle?
YES >>
1. Stop the vehicle.
2. Go to AT-60, "Cruise Test - Part 2". Cruise Test Part 2
NO >> Enter a check mark at "Engine Speed Does Not Return To Idle" on the "DIAGNOSTIC WORKSHEET", then continue the road test. Go to AT-60, "Cruise Test - Part 2". Cruise Test Part 2