Assembly Inspection and Adjustment
ASSEMBLY INSPECTION AND ADJUSTMENT^ Before inspection and adjustment, drain gear oil.
Total Preload Torque
1. Rotate drive pinion back and forth 2 to 3 times to check for unusual noise and rotation malfunction.
2. Rotate drive pinion at least 20 times to check for smooth operation of the bearing.
3. Measure total preload with preload gauge.
Tool number A: ST3127S000 (J-25765-A)
Total preload torque: 1.56 - 2.65 Nm (0.16 - 0.27 kg-m, 14 - 23 inch lbs.)
NOTE: Total preload torque = Pinion bearing preload torque + Side bearing preload torque
^ If measured value is out of the specification, disassemble it to check and adjust each part. Adjust the pinion bearing preload and side bearing preload. Adjust the pinion bearing preload first, then adjust the side bearing preload.
When the preload torque is large
On pinion bearings: Decrease the drive pinion bearing adjusting washer and drive pinion adjusting washer thickness.
On side bearings: Increase the side bearing adjusting shim thickness.
When the preload torque is small
On pinion bearings: Increase the drive pinion bearing adjusting washer and drive pinion adjusting washer thickness.
On side bearings: Decrease the side bearing adjusting shim thickness.
Drive Gear Runout
1. Remove carrier cover.
2. Fit a dial indicator to the drive gear back face.
3. Rotate the drive gear to measure runout.
Runout limit: 0.05 mm (0.0020 inch)
^ If the runout is outside of the repair limit, check drive gear assembly condition; foreign material may be caught between drive gear and differential case, or differential case or drive gear may be deformed, etc.
CAUTION: Replace drive gear and drive pinion gear as a set.
Tooth Contact
1. Remove carrier cover.
2. Apply red lead to drive gear.
CAUTION: Apply red lead to both the faces of 3 to 4 gears at 4 locations evenly spaced on drive gear.
3. Rotate drive gear back and forth several times, check drive pinion gear to drive gear tooth contact.
CAUTION: Check tooth contact on drive side and reverse side.
4. If tooth contact is improperly adjusted, follow the procedure below to adjust the pinion height (dimension X).
^ If the tooth contact is near the face (face contact), or near the heel (heel contact), thicken pinion height adjusting washers to move drive pinion closer to drive gear.
^ If the tooth contact is near the flank (flank contact), or near the toe (toe contact), thin pinion height adjusting washers to move drive pinion farther from drive gear.
Backlash
1. Remove carrier cover.
2. Fit a dial indicator to the drive gear face to measure the backlash.
Backlash: 0.10 - 0.15 mm (0.0039 - 0.0059 inch)
^ If the backlash is outside of the specified value, change the thickness of side bearing adjusting washer.
When the backlash is large: Decrease side bearing adjusting washer thickness.
When the backlash is small: Increase side bearing adjusting washer thickness.
Companion Flange Runout
1. Fit a dial indicator onto the companion flange face (inner side of the propeller shaft mounting bolt holes).
2. Rotate companion flange to check for runout.
Runout limit: 0.18 mm (0.0070 inch)
3. Fit a test indicator to the inner side of companion flange (socket diameter).
4. Rotate companion flange to check for runout.
Runout limit: 0.13 mm (0.0051 inch)
5. If the runout value is outside the runout limit, follow the procedure below to adjust.
a. Check for runout while changing the phase between companion flange and drive pinion by 90° step, and search for the position where the runout is the minimum.
b. If the runout value is still outside of the limit after the phase has been changed, possible cause will be an assembly malfunction of drive pinion and pinion bearing and malfunction of pinion bearing. Check for these items and repair if necessary.
c. If the runout value is still outside of the limit after the check and repair, replace companion flange.