A/T Does Not Shift: D4 -> D5
A/T Does Not Shift: D4 -> D5SYMPTOM:
^ The vehicle does not shift-up from the D4 to D5 gear at the specified speed.
^ The vehicle does not shift-up from the D4 to D5 gear unless A/T is warmed up.
DIAGNOSTIC PROCEDURE
1. CONFIRM THE SYMPTOM
Check if vehicle creeps forward in "D" position and vehicle can be started from D1.
OK or NG
OK >> GO TO 2.
NG >> Refer to AT-199, "Vehicle Does Not Creep Forward in "D" Position", AT-201, "Vehicle Cannot Be Started From D1".
Vehicle Does Not Creep Forward In D Position
Vehicle Cannot Be Started From D1
2. CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to AT-92, "SELF-DIAGNOSTIC RESULT MODE", AT-102, "TCM SELF-DIAGNOSTIC PROCEDURE (NO TOOLS)".
Self-Diagnostic Result Mode
TCM Self-Diagnostic Procedure (No Tools)
Is any malfunction detected by self-diagnostic results?
YES >> Check the malfunctioning system. Refer to AT-92, "SELF-DIAGNOSTIC RESULT MODE", AT-103, "Judgement Self-diagnosis Code".
Self-Diagnostic Result Mode
TCM Self-Diagnostic Procedure (No Tools)
NO >> GO TO 3.
3. CHECK A/T FLUID LEVEL
Check A/T fluid level.
OK or NG
OK >> GO TO 4.
NG >> Refill [1][2]ATF.
4. CHECK LINE PRESSURE
Check line pressure at the engine stall point. Refer to AT-54, "LINE PRESSURE TEST". Line Pressure Test
OK or NG
OK >> GO TO 7.
NG-1 >> Line pressure high: GO TO 5.
NG-2 >> Line pressure low: GO TO 6.
5. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM.
2. Disassemble A/T.
3. Check the following.
- Oil pump assembly.
OK or NG
OK >> GO TO 7.
NG >> Repair or replace damaged parts.
6. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM.
2. Disassemble A/T.
3. Check the following.
- Oil pump assembly.
- Power train system.
- Transmission case.
OK or NG
OK >> GO TO 7.
NG >> Repair or replace damaged parts.
7. CHECK A/T FLUID CONDITION
1. Remove oil pan.
2. Check A/T fluid condition. Refer to AT-53, "A/T Fluid Condition Check". A/T Fluid Condition Check
OK or NG
OK >> GO TO 8.
NG >> GO TO 11.
8. DETECT MALFUNCTIONING ITEM
Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to AT-64, "Symptom Chart" (Symptom No.13). Symptom Chart
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.
9. CHECK SYMPTOM
Check again. Refer to AT-58, "Cruise Test - Part 1". Cruise Test - Part 1
OK or NG
OK >> INSPECTION END
NG >> GO TO 10.
10. CHECK TCM
1. Check TCM input/output signals. Refer to AT-89, "TCM Input/Output Signal Reference Values". Pinout Values and Diagnostic Parameters
2. If NG, recheck A/T assembly harness connector terminals for damage or loose connection with harness connector.
OK or NG
OK >> INSPECTION END
NG >> Repair or replace damaged parts.
11. DETECT MALFUNCTIONING ITEM
Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to AT-64, "Symptom Chart" (Symptom No.13). Symptom Chart
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.