Reprogramming the Unified Meter and A/C Amp
Reprogramming the Unified Meter and A/C AmpIMPORTANT:
^ Before starting make sure your ASIST has been freshly synchronized and all C-III upgrades have been installed. The Unified Meter and A/C Amp reprogramming software is delivered via ASIST synchronization.
^ This reprogramming process requires an Internet connection. Make sure the C-III computer has an Internet connection before starting.
^ The C-III computer must have the ability to print the calibration report while cable-connected to the vehicle.
^ The software will not allow reprogramming of vehicles that are not affected by this campaign.
^ The reprogramming can only be applied one time to each affected vehicle. Vehicle identification is validated against data located on NNA's servers before reprogramming is allowed.
1. Use the USB cable to connect the Vehicle Interface (VI) to the C-III computer and then connect the VI to the vehicle.
2. Connect the AC Adapter to the C-III computer.
3. Make sure the C-III computer is connected to the PC Converter Box (J-50419-1) with the USB cable.
4. Turn the Ignition ON.
NOTE:
With the ignition ON the odometer screen should be blank.
If the odometer screen is not blank:
a. Turn the ignition OFF.
b. Turn the C-III computer OFF.
c. Disconnect and reconnect all of the reprogramming cables (see Figure 22 above). Make sure all connectors are securely connected.
d. Make sure the USB cables and A/C power supply are securely connected to the C-III computer.
e. Make sure the VI is securely connected to the vehicle.
f. Go back and restart with Step 1 above.
5. Turn ON the C-III computer (do not start C-III at this time).
^ The first time the reprogramming kit (PC converter box) is attached to either of the C-III USB ports the screens above (Figures lb - 1 d) will display.
^ If this is not the first time these screens will not display - go to step 6.
NOTE
This sequence of 3 screens will display twice. Perform a through d twice.
a. Select Install the software automatically (Recommended).
b. Select Next
c. Select Continue Anyway
d. Select Finish
6. Open / start ASIST.
7. Select Information Tool Box and then Specialty Tools.
8. Select FX. Odometer Calibration Tool.
9. After selecting FX. Odometer Calibration Tool, C-III will launch automatically.
10. Wait for the Detecting VI/MI in progress message to clear.
11. Select the Detected VI from the list.
12. Select Connect.
13. Wait for the Checking the firmware version message to clear.
14. Wait for a few seconds while the reprogramming software obtains the VIN.
15. The FX Odometer Calibration Tool will launch automatically (Figure 1 h).
16. The VIN will automatically display.
17. Enter the Technician Name.
18. Select Start
19. Select I Agree
^ After selecting I Agree the reprogramming/calibration process will begin automatically and take only a few seconds to complete.
If the calibration process does not complete within 1 minute, or an error message is displayed:
a. Turn the ignition OFF
b. Turn the C-III computer OFF.
c. Disconnect and reconnect all of the reprogramming cables (see Figure 22 above). Make sure all connectors are securely connected.
d. Make sure USB cable and A/C power supply are securely connected to the C-III computer.
e. Make sure the Internet connection is working.
f. Go back to "Reprogramming the Unified Meter and A/C Amp" and restart with Step 1.
20. When the calibration process has completed successfully the message in Figure 1j will display.
21. Turn the ignition OFF and select Continue.
22. With the ignition OFF wait for 2 minutes.
^ The screen in Figure 1k will display with a 2 minute countdown
23. After waiting 2 minutes the Calibration Completion Report will display (Figure 1I)
24. Print the Calibration Completion Report and attach it to the repair order for warranty documentation.
25. Disconnect C-III and the reprogramming equipment.
26. Reassemble all parts removed in reverse order.