Part 2
Exploded View AT-274 (Part 1):
Exploded View AT-274 (Part 2):
Exploded View AT-276 (Part 1):
Exploded View AT-276 (Part 2):
Exploded View AT-278 (Part 1):
Exploded View AT-278 (Part 2):
Exploded View AT-280 (Part 1):
Exploded View AT-280 (Part 2):
Exploded View AT-283 (Part 1):
Exploded View AT-283 (Part 2):
Exploded View AT-284 (Part 1):
Exploded View AT-284 (Part 2):
Exploded View AT-286 (Part 1):
Exploded View AT-286 (Part 2):
Assembly(1)(continued)
25. As shown in the figure, use the drift to drive rear oil seal into the rear extension (2WD models) or adapter case (AWD models) until it is flush.
CAUTION:
^ Do not reuse rear oil seal.
^ Apply [1][2]ATF to rear oil seal.
26. Install return spring to parking pawl.
^ VQ35DE models
^ VK45DE models
- Return spring (1)
- Parking pawl (2)
27. Install parking pawl (with return spring) and pawl shaft to rear extension (2WD models) or adapter case (AWD models).
28. Install parking actuator support to rear extension (2WD models) or adapter case (AWD models).
29. Install needle bearing to rear extension (2WD models) or adapter case (AWD models).
CAUTION:
^ Take care with the direction of needle bearing.
^ Apply petroleum jelly to needle bearing.
30. Install seal rings to output shaft.
CAUTION:
^ Do not reuse seal rings.
^ Apply petroleum jelly to seal rings.
31. Install parking gear to output shaft.
32. Install output shaft in transmission case.
CAUTION: Be careful not to mistake front for rear because both sides looks similar. (Thinner end is front side.)
33. Install bearing race to output shaft.
34. Install rear extension assembly (2WD models) or adapter case assembly (AWD models) according to the following procedures.
a. 2WD models
i. Apply recommended sealant (Genuine Anaerobic Liquid Gasket or equivalent. Refer to GI-48, "Recommended Chemical Products and Sealants".) to rear extension assembly as shown in the figure. Tools and Equipment
CAUTION: Completely remove all moisture, oil and old sealant, etc. from the transmission case and rear extension assembly mounting surfaces.
ii. Install rear extension assembly to transmission case.
CAUTION: Insert the tip of parking rod between the parking pawl and the parking actuator support when assembling the rear extension assembly.
iii. Tighten rear extension assembly mounting bolts to specified torque. Refer to Exploded View AT-274.
CAUTION: Do not reuse self-sealing bolts.
b. AWD models
i. Install gasket onto transmission case.
CAUTION:
^ Do not reuse gasket.
^ Completely remove all moisture, oil and old gasket, etc. from the transmission case and adapter case assembly mounting surfaces.
ii. Install adapter case assembly to transmission case.
CAUTION: Insert the tip of parking rod between the parking pawl and the parking actuator support when assembling the rear extension assembly.
iii. Tighten adapter case assembly mounting bolts (1) to specified torque. [With bracket (2).] Refer to Exploded View AT-274.
<-: Bolt (10)
CAUTION:
^ Do not reuse self-sealing bolts (3).
35. Install needle bearing in drum support.
CAUTION:
^ Take care with the direction of needle bearing.
^ Apply petroleum jelly to needle bearing.
36. Install direct clutch assembly in reverse brake.
CAUTION: Make sure that drum support edge surface and direct clutch inner boss edge surface come to almost same place.
37. Install high and low reverse clutch assembly in direct clutch.
38. Using a flat-bladed screwdriver, align drive plate.
39. Install high and low reverse clutch hub, mid sun gear assembly and rear sun gear assembly as a unit.
CAUTION: Check that portion "A" of high and low reverse clutch drum protrudes approximately 2 mm (0.08 in) beyond portion "B" of rear sun gear.
40. Install needle bearing in rear carrier assembly.
CAUTION:
^ Take care with the direction of needle bearing.
^ Apply petroleum jelly to needle bearing.
41. Install bearing race in rear carrier assembly.
CAUTION: Apply petroleum jelly to bearing race.
42. Install rear carrier assembly in direct clutch drum.
43. Install needle bearing (rear side) to mid carrier assembly.
CAUTION:
^ Take care with the direction of needle bearing.
^ Apply petroleum jelly to needle bearing.
44. Install needle bearing (front side) to mid carrier assembly.
CAUTION:
^ Take care with the direction of needle bearing.
^ Apply petroleum jelly to needle bearing.
45. Install mid carrier assembly in rear carrier assembly.
46. Install front carrier assembly, input clutch assembly and rear internal gear as a unit.
47. Install seal rings in input clutch assembly.
CAUTION:
^ Do not reuse seal rings.
^ Apply petroleum jelly to seal rings.
48. Install band servo anchor end pin and lock nut in transmission case.
CAUTION: Do not reuse band servo anchor end pin.
49. Install brake band in transmission case.
CAUTION: Assemble it so that identification to avoid incorrect installation faces servo side.
50. Install front sun gear to front carrier assembly.
CAUTION: Apply [1][2]ATF to front sun gear bearing and 3rd one-way clutch end bearing.
51. Install needle bearing to front sun gear.
CAUTION:
^ Take care with the direction of needle bearing.
^ Apply petroleum jelly to needle bearing.
52. Adjust brake band tilting using clips so that brake band contacts front sun gear drum evenly.
53. Adjust brake band.
a. Loosen lock nut.
b. Tighten band servo anchor end pin to the specified torque.
Torque: 5.0 Nm (0.51 kg-m, 44 in-lb)
c. Back of band servo anchor end pin three turns.
d. Holding band servo anchor end pin, tighten lock nut to the specified torque. Refer to Exploded View AT-274.