Inspection After Disassembly
INSPECTION AFTER DISASSEMBLYShift Rod Components
^ Check the working face of the shift rod and fork for wear, partial wear, bending and other abnormality. If any is found, replace with a new one.
^ Measure the clearance between the shift fork and sleeve. If it is out of specification, replace it with a new one.
Specification: Less than 0.36 mm (0.0142 in)
Planetary Carrier
^ Measure the end play of each pinion gear. If it is out of specification, replace the planetary carrier assembly with a new one.
Pinion gear end play: 0.1 - 0.7 mm (0.004 - 0.028 in)
^ Check the working face of each gear and bearing for damage, burrs, partial wear, dents and other abnormality. If any is found, replace the planetary carrier assembly with a new one.
Sun Gear
^ Check if the oil passage of the sun gear assembly is clogged. For this, try to pass a 3.6 mm (0.142 in) dia. pin through the oil passage as shown.
^ Check the sliding and contact surface of each gear and bearing for damage, burrs, partial wear, dents, and other abnormality. If any is found, replace the sun gear assembly with a new one.
Internal Gear
^ Check the internal gear teeth for damage, partial wear, dents and other abnormality. If any is found, replace the internal gear with a new one.
Gears and Drive Chain
^ Check the gear faces and shaft for wear, cracks, damage, and seizure.
^ Check the surfaces which contact the sun gear, clutch drum, clutch hub, press flange, clutch piston and each bearing for damage, peel, partial wear, dents, bending, or other abnormal damage. If any is found, replace with a new one.
Bearing
^ Make sure the bearings roll freely and are free from noise, pitting and cracks.
Main Oil Pump
1. Check the inner and outer circumference, tooth face, and side-face of the inner and outer gears for damage or abnormal wear.
2. Measure the side clearance between the main oil pump housing edge and the inner and outer gears.
3. Make sure the side clearance is within specification. If the measurement is out of specification, replace the inner and outer gears with new ones as a set.
Specification: 0.015 - 0.035 mm (0.0006 - 0.0014 in)
Sub-oil Pump
1. Check the inner and outer circumference, tooth face, and side-face of the inner and outer gears for damage or abnormal wear.
2. Measure the side clearance between the sub oil pump housing edge and the inner and outer gears.
3. Make sure the side clearance is within specification. If the measurement is out of specification, replace the inner and outer gears with new ones as a set.
Specification: 0.015 - 0.035 mm (0.0006 - 0.0014 in)
Control Valve
^ Check resistance between the terminals of the clutch pressure solenoid valve, 2-4WD shift solenoid valve, clutch pressure switch, line pressure switch and the transfer fluid temperature sensor.
^ Check the sliding faces of the control valves and plugs for abnormality. If any is found, replace the control valve assembly with a new one.
CAUTION: Replace control valve body together with clutch return spring as a set.
^ Check each control valve spring for damage or distortion. Also check its free length, outer diameter and wire diameter. If any damage or fatigue is found, replace the control valve body with a new one.
CAUTION: Replace control valve body together with clutch return spring as a set.
Clutch
^ Check the drive plate facings and driven plate for damage, cracks or other abnormality. If any abnormalities are found, replace with a new one.
^ Check the thickness of the drive plate facings and driven plate.
CAUTION:
^ Measure facing thickness at 3 points to take an average.
^ Check all drive and driven plates.
^ Check return spring for damage or deformation.
^ Do not remove spring from plate.
Return Spring
^ Check the stamped mark shown. Then, check that the free lengths, (include thickness of plate) are within specifications. If any abnormality is found, replace with a new return spring assembly of the same stamped number.