Snow Mode Switch
SNOW MODE SWITCH
Description
The snow mode switch signal is sent to the "unified meter and A/C amp." from the snow mode switch. The
"unified meter and A/C amp." then sends the signal to the ECM via the CAN communication line.
The snow mode is used for driving or starting the vehicle on snowy roads or slippery areas. If the snow mode is activated, the vehicle speed will not accelerates as quickly as normal to avoid vehicle slip. In other words, ECM controls rapid engine torque change by controlling the electric throttle control actuator operating speed.
Component Function Check
1. CHECK SNOW MODE SWITCH FUNCTION
1.Turn ignition switch ON.
2.Select "SNOW MODE SW" in "DATA MONITOR" mode with CONSULT.
3.Check "SNOW MODE SW" indication under the following conditions.
Is the inspection result normal?
YES- GO TO 2.
NO- Go to "Diagnosis Procedure" .
2. CHECK SNOW MODE INDICATOR FUNCTION
1.Turn ignition switch ON.
2.Check the snow mode indicator in the snow mode switch under the following condition.
Is the inspection result normal?
YES- INSPECTION END
NO- Go to "Diagnosis Procedure" .
Diagnosis Procedure
1. CHECK SNOW MODE SWITCH OVERALL FUNCTION
Confirm the malfunctioning circuit (snow mode switch or snow mode indicator). Refer to "Component Function Check" .
Which circuit is related to the incident?
Snow mode switch-GO TO 2.
Snow mode indicator-GO TO 6.
2. CHECK DTC WITH "UNIFIED METER AND A/C AMP."
Refer to "CONSULT Function (METER/M&A)" CONSULT Function.
Is the inspection result normal?
YES- GO TO 3.
NO- Go to "Work flow" Work Flow.
3. CHECK SNOW MODE SWITCH POWER SUPPLY CIRCUIT
1.Turn ignition switch OFF.
2.Disconnect snow mode switch harness connector.
3.Turn ignition switch ON.
4.Check the voltage between snow mode switch harness connector and ground.
Is the inspection result normal?
YES- GO TO 5.
NO- GO TO 4.
4. DETECT MALFUNCTIONING PART
Check the following.
- Harness connectors E106, M6
- Harness connectors M134, M170
- IPDM E/R harness connector E7
- 10 A fuse (No. 43)
- Harness for open or short between snow mode switch and fuse.
- Repair open circuit, short to ground or short to power in harness or connectors.
5. CHECK SNOW MODE SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.Turn ignition switch OFF.
2.Disconnect "unified meter and A/C amp." harness connector.
3.Check the continuity between snow mode switch harness connector and "unified meter and A/C amp."
harness connector.
4.Also check harness for short to ground and short to power.
Is the inspection result normal?
YES- GO TO 8.
NO- Repair open circuit, short to ground or short to power in harness or connector.
6. CHECK GROUND CONNECTION
1.Turn ignition switch OFF.
2.Check ground connection M95. Refer to Ground Inspection in "Circuit Inspection" Circuit Inspection.
Is the inspection result normal?
YES- GO TO 7.
NO- Repair or replace ground connection.
7. CHECK SNOW MODE INDICATOR LAMP GROUND CIRCUIT FOR OPEN AND SHORT
1.Check the continuity between snow mode switch harness connector and ground.
2.Also check harness for short to power.
Is the inspection result normal?
YES- GO TO 8.
NO- Repair open circuit or short to power in harness or connectors.
8. CHECK SNOW MODE SWITCH
Refer to "Component Inspection" .
Is the inspection result normal?
YES- GO TO 9.
NO- Replace snow mode switch. Refer to "Exploded View" Exploded View.
9. CHECK INTERMITTENT INCIDENT
Refer to "Intermittent Incident" Intermittent Incident.
- INSPECTION END
Component Inspection
1. CHECK SNOW MODE SWITCH-I
1.Turn ignition switch OFF.
2.Disconnect snow mode switch harness connector.
3.Check the continuity between snow mode switch terminals under the following conditions.
Is the inspection result normal?
YES- GO TO 2.
NO- Replace snow mode switch. Refer to "Exploded View" Exploded View.
2. CHECK SNOW MODE SWITCH-II
Check the continuity between snow mode switch terminals under the following conditions.
Is the inspection result normal?
YES- INSPECTION END
NO- Replace snow mode switch. Refer to "Exploded View" Exploded View.