Front Seat

FRONT SEAT

Disassembly and Assembly


SEATBACK

Disassembly
1.Remove the seatback board.





- Remove the clips and pawls, and then pull out seatback board.
- Pull down the seatback board to release the upper pawls.





2.Remove the seatback trim retainer and seatback trim band from seat cushion frame.
3.Disconnect the harness connectors and remove the harness clamps.





- Disconnect the reclining motor harness connector (A) and lumbar support harness connector (Power lumber support seat only) (B).





- Disconnect the seatback heater seat harness connector (C).
(With heater seat only)





- Remove the harness clamps, and then side air bag module harness (D).





4.Remove the metal clips and pawls, and then pull out seat cushion front finisher.





5.Remove the seat cushion outer finisher.





- Remove the seat slide & lifter switch knob and seat reclining switch knob.
- Remove the clips, metal clips and pawls, and then pull out seat cushion outer finisher outside.
- Disconnect the seat slide & lifter, seat reclining and lumbar support switch (Power lumber support seat only) harness connectors.










6.Remove the seat cushion outer finisher inside front (1) and rear (2).





7.Remove the metal clip and pawls, and then pull out seat cushion inner finisher outside.










8.Remove the seat cushion inner finisher inside front (1) and rear (2).
9.Remove the lumber support lever knob. (Manual lumber support seat only)





Pull snap ring (1) upward, and remove lumber support lever knob (2) from seatback frame. Using a hook and pick tool.
10.Remove the seatback trim and seatback pad.





- Remove the headrest holder.

CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
- Remove the side air bag module.
- Remove the seatback trim and seatback pad from the seatback frame.
- Remove the hog rings, and separate the seatback trim and seatback pad.
11.Remove the seatback silencer.
12.Remove the seatback frame.





Remove the seatback frame mounting bolts (A) and then remove the seatback frame.
Assembly
Assemble in the reverse order of disassembly.

CAUTION:
Install the hog rings of seatback trim in position, and then securely connect the trim or trim cord with the pad side wire.

SEAT CUSHION

Disassembly

CAUTION:
Never disassemble front passenger seat cushion assembly.
Always replace as an assembly.
For front passenger seat service parts, refer to the service part catalogue.





1.Remove the seatback board.
- Remove the clips and pawls, and then pull out seatback board.
- Pull down the seatback board to release the upper pawls.





2.Remove the seatback trim retainer and seatback trim band from seat cushion frame.
3.Disconnect the harness connectors and remove the harness clamps.





- Disconnect the reclining motor harness connector (A) and lumbar support harness connector (B) (Power lumber support seat only).





- Disconnect the seatback heater seat harness connector (C).
(With heater seat only.)





- Remove the side air bag module harness (D).





4.Remove the metal clips and pawls, and then pull out seat cushion front finisher.





5.Remove the seat cushion outer finisher.





- Remove the seat slide & lifter switch knob and seat reclining switch knob.
- Remove the clips, metal clips and pawls, and then pull out seat cushion outer finisher outside.
- Disconnect the seat slide & lifter, seat reclining and lumbar support switch (Power lumber support seat only) harness connectors.










6.Remove the seat cushion outer finisher inside front (1) and rear (2).





7.Remove the metal clip and pawls, and then pull out seat cushion inner finisher outside.










8.Remove the seat cushion inner finisher inside front (1) and rear (2).
9.Remove the seatback assembly.





Remove the seatback assembly mounting bolts (A).





10.Remove the metal clips, and then pull out seat cushion outer lower finisher outside (1) and inside (2).










11.Remove the seat cushion inner lower finisher.





12.Remove the seat cushion trim and seat cushion pad. (Without occupant classification system control unit model)





- Disconnect the seat cushion heater unit harness connector (A).
- Remove the seat cushion trim retainer.
- Remove the hog rings, and separate the seat cushion trim and seat cushion pad.
13.Remove the seat belt buckle. Refer to "SEAT BELT BUCKLE : Removal and Installation" Removal and Installation.
14.Remove the driver seat control unit (with automatic drive positioner seat only). Refer to "Removal and Installation" Removal and Installation.
15.Remove the heated seat control unit. Refer to "Removal and Installation" Removal and Installation.
Assembly
Assemble in the reverse order of disassembly.

CAUTION:
Install the hog rings of seat cushion trim in position, and then securely connect the trim or trim cord with the pad side wire.