ICC Brake Switch
P1572 ICC BRAKE SWITCH
DTC Logic
DTC DETECTION LOGIC
NOTE:
-If DTC P1572 is displayed with DTC P0605, first perform the trouble diagnosis for DTC P0605. Refer to "DTC Logic" P0605.
-This self-diagnosis has the one trip detection logic. When malfunction A is detected, DTC is not stored in ECM memory. And in that case, 1st trip DTC and 1st trip freeze frame data are displayed.
1st trip DTC is erased when ignition switch is turned OFF. And even when malfunction A is detected in two consecutive trips, DTC is not stored in ECM memory.
DTC CONFIRMATION PROCEDURE
1. PRECONDITIONING
1.Turn ignition switch OFF and wait at least 10 seconds.
2.Turn ignition switch ON.
3.Turn ignition switch OFF and wait at least 10 seconds.
NOTE:
The procedure for malfunction B is not described. It takes an extremely long time to complete the procedure for malfunction B. By performing the procedure for malfunction A, the condition that causes malfunction B can be detected.
- GO TO 2.
2. PERFORM DTC CONFIRMATION PROCEDURE
1.Start engine (VDC switch OFF).
2.Press MAIN switch and check that CRUISE indicator is displayed in combination meter.
3.Drive the vehicle for at least 5 consecutive seconds under the following conditions.
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
This procedure may be conducted with the drive wheels lifted in the shop or by driving the vehicle.
If a road test is expected to be easier, it is unnecessary to lift the vehicle.
4.Check 1st trip DTC.
Is 1st trip DTC detected?
YES- Proceed to "Diagnosis Procedure" .
NO- GO TO 3.
3. PERFORM DTC CONFIRMATION PROCEDURE
1.Drive the vehicle for at least 5 consecutive seconds under the following conditions.
CAUTION:
Revision: March 20122013 Infiniti JX
Always drive vehicle at a safe speed.
NOTE:
This procedure may be conducted with the drive wheels lifted in the shop or by driving the vehicle.
If a road test is expected to be easier, it is unnecessary to lift the vehicle.
2.Check 1st trip DTC.
Is 1st trip DTC detected?
YES- Proceed to "Diagnosis Procedure" .
NO- INSPECTION END
Diagnosis Procedure
1. CHECK OVERALL FUNCTION-I
With CONSULT
1.Turn ignition switch ON.
2.Select "BRAKE SW1" in "DATA MONITOR" mode with CONSULT.
3.Check "BRAKE SW1" indication under the following conditions.
Without CONSULT
1.Turn ignition switch ON.
2.Check the voltage between ECM harness connector terminals under the following conditions.
Is the inspection result normal?
YES- GO TO 2.
NO- GO TO 3.
2. CHECK OVERALL FUNCTION-II
With CONSULT
Select "BRAKE SW2" and check indication under the following conditions.
Without CONSULT
Check the voltage between ECM harness connector terminals as per the following.
Revision: March 20122013 Infiniti JX
Is the inspection result normal?
YES- Check intermittent incident. Refer to "Intermittent Incident" Intermittent Incident.
NO- GO TO 6.
3. CHECK ICC BRAKE SWITCH POWER SUPPLY
1.Turn ignition switch OFF.
2.Disconnect ICC brake switch harness connector.
3.Turn ignition switch ON.
4.Check the voltage between ICC brake switch harness connector and ground.
Is the inspection result normal?
YES- GO TO 4.
NO- Perform the trouble diagnosis for power supply circuit.
4. CHECK ICC BRAKE SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.Turn ignition switch OFF.
2.Disconnect ECM harness connector.
3.Check the continuity between ICC brake switch harness connector and ECM harness connector.
4.Also check harness for short to ground and short to power.
Is the inspection result normal?
YES- GO TO 5.
NO- Repair or replace error-detected parts.
5. CHECK ICC BRAKE SWITCH
Check ICC brake switch. Refer to "Component Inspection (ICC Brake Switch)" .
Is the inspection result normal?
YES- Check intermittent incident. Refer to "Intermittent Incident" Intermittent Incident.
NO- Replace ICC brake switch. Refer to "Exploded View" Exploded View.
6. CHECK STOP LAMP SWITCH POWER SUPPLY
1.Turn ignition switch OFF.
2.Disconnect stop lamp switch harness connector.
3.Disconnect ICC brake hold relay harness connector.
4.Check the voltage between stop lamp switch harness connector and ground.
5.Check the voltage between ICC brake hold relay harness connector and ground.
Revision: March 20122013 Infiniti JX
Is the inspection result normal?
YES- GO TO 7.
NO- Perform the trouble diagnosis for power supply circuit.
7. CHECK STOP LAMP SWITCH INPUT SIGNAL CIRCUIT
1.Disconnect ECM harness connector.
2.Check the continuity between stop lamp switch harness connector and ECM harness connector.
3.Check the continuity between ICC brake hold relay harness connector and ECM harness connector.
4.Also check harness for short to ground and short to power.
Is the inspection result normal?
YES- GO TO 8.
NO- Repair or replace error-detected parts.
8. CHECK STOP LAMP SWITCH
Check stop lamp switch. Refer to "Component Inspection (Stop Lamp Switch)" .
Is the inspection result normal?
YES- GO TO 9.
NO- Replace stop lamp switch. Refer to "Exploded View" Exploded View.
9. CHECK ICC BRAKE HOLD RELAY
Check ICC brake hold relay. Refer to "Component Inspection (ICC Brake Hold Relay)" .
Is the inspection result normal?
YES- Check intermittent incident. Refer to "Intermittent Incident" Intermittent Incident.
NO- Replace ICC brake hold relay.
Component Inspection (ICC Brake Switch)
1. CHECK ICC BRAKE SWITCH-I
1.Turn ignition switch OFF.
2.Disconnect ICC brake switch harness connector.
3.Check the continuity between ICC brake switch terminals under the following conditions.
Is the inspection result normal?
YES- INSPECTION END
NO- GO TO 2.
2. CHECK ICC BRAKE SWITCH-II
1.Adjust ICC brake switch installation. Refer to "Adjustment" Adjustments.
Revision: March 20122013 Infiniti JX
2.Check the continuity between ICC brake switch terminals under the following conditions.
Is the inspection result normal?
YES- INSPECTION END
NO- Replace ICC brake switch. Refer to "Exploded View" Exploded View.
Component Inspection (Stop Lamp Switch)
1. CHECK STOP LAMP SWITCH-I
1.Turn ignition switch OFF.
2.Disconnect stop lamp switch harness connector.
3.Check the continuity between stop lamp switch terminals under the following conditions.
Is the inspection result normal?
YES- INSPECTION END
NO- GO TO 2.
2. CHECK STOP LAMP SWITCH-II
1.Adjust stop lamp switch installation. Refer to "Adjustment" Adjustments.
2.Check the continuity between stop lamp switch terminals under the following conditions.
Is the inspection result normal?
YES- INSPECTION END
NO- Replace stop lamp switch. Refer to "Exploded View" Exploded View.
Component Inspection (ICC Brake Hold Relay)
1. CHECK ICC BRAKE HOLD RELAY
1.Turn ignition switch OFF.
2.Remove ICC brake hold relay.
3.Check the continuity between ICC brake hold relay terminals under the following conditions.
Is the inspection result normal?
YES- INSPECTION END
NO- Replace ICC brake hold relay
Revision: March 20122013 Infiniti JX